Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › ACOUSTIC VEHICLE ALERTING SYSTEM
RM37H0E _59 Vehicle Exterior _095082 ACOUSTIC VEHICLE ALERTING SYSTEM _0447221 ACOUSTIC VEHICLE ALERTING SYSTEM C

ACOUSTIC VEHICLE ALERTING SYSTEM  ACOUSTIC VEHICLE ALERTING SYSTEM  B1350  Speaker Circuit  


DESCRIPTION

The vehicle approaching speaker assembly circuit consists of the vehicle approaching speaker controller and vehicle approaching speaker assembly.

This DTC is stored when a malfunction is detected in the vehicle approaching speaker assembly circuit or vehicle approaching speaker controller.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1350 Speaker Circuit
Detection condition (1):

The ignition switch is ON.


Detection condition (2):

IG power source voltage is 10 V or more.


Malfunction status (1):

When ECU output sound signal is being monitored with warning sound not being output, a speaker circuit open, short or short to ground is detected.


Malfunction status (2):

When vehicle proximity warning sound output conditions are met, an internal malfunction is continuously detected in the vehicle approaching speaker controller.


Malfunction duration (1):

6 seconds or more


Malfunction duration (2):

3 seconds or more


·

Vehicle approaching speaker controller

·

Vehicle approaching speaker assembly

·

Harness or connector


Vehicle Proximity Notification System A

WIRING DIAGRAM

E402276E66
0.729,1.823 1.188,2.021 0.458,0.198 10 false A25 0.771,2.021 3.302,2.24 2.531,0.219 10 false Vehicle Approaching Speaker Assembly 4.656,1.938 5.688,2.135 1.031,0.198 10 false D97 4.667,2.094 7.156,2.26 2.49,0.167 10 false Vehicle Approaching Speaker Controller 2.104,0.969 2.563,1.167 0.458,0.198 10 false 2 2.104,1.375 2.563,1.573 0.458,0.198 10 false 1 4.75,0.99 5.208,1.188 0.458,0.198 10 false 7 4.75,1.375 5.208,1.573 0.458,0.198 10 false 8 4.938,1.073 5.396,1.271 0.458,0.198 10 false SP+ 4.938,1.49 5.396,1.688 0.458,0.198 10 false SP-

PROCEDURE

1.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY

OK

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)

NG

REPLACE VEHICLE APPROACHING SPEAKER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)

Pre-procedure 1

a.

Disconnect the D97 vehicle approaching speaker controller connector.


Procedure 1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A25,D97)Location & Routing

Click Connector(A25)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Vehicle Approaching Speaker Assembly

Click Connector(D97)Instrument Panel>Instrument Panel Wire>Vehicle Approaching Speaker Controller

A25-2 - D97-7 (SP+) Always Below 1 Ω
A25-1 - D97-8 (SP-) Always Below 1 Ω
A25-2 or D97-7 (SP+) - Body ground Always 10 kΩ or higher
A25-1 or D97-8 (SP-) - Body ground Always 10 kΩ or higher



Post-procedure 1

c.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR