Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › ACOUSTIC VEHICLE ALERTING SYSTEM
RM37H0E _59 Vehicle Exterior _095082 ACOUSTIC VEHICLE ALERTING SYSTEM _0447221 ACOUSTIC VEHICLE ALERTING SYSTEM J

ACOUSTIC VEHICLE ALERTING SYSTEM  ACOUSTIC VEHICLE ALERTING SYSTEM  There is No Sound Made  


DESCRIPTION

Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.

WIRING DIAGRAM

E458715E01
5.594,5.75 6.885,6.26 1.292,0.51 10 false Vehicle Approaching Speaker Assembly 4.5,4.948 4.958,5.146 0.458,0.198 10 false SP+ 4.51,5.24 4.969,5.438 0.458,0.198 10 false SP- 4.469,6.969 4.927,7.167 0.458,0.198 10 false GND 3.354,7.833 6.021,8.115 2.667,0.281 10 false Vehicle Approaching Speaker Controller 0.771,7.469 2.688,7.76 1.917,0.292 10 false Combination Meter Assembly 0.802,2.365 2.583,2.708 1.781,0.344 10 false Hybrid Vehicle Control ECU 0.844,4.052 2.5,4.542 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.771,5.792 2.802,6.146 2.031,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.042,0.885 3.031,1.094 0.99,0.208 10 false IG1 D NO.1 0.438,0.74 1.49,1.135 1.052,0.396 10 false from IG1 D NO.1 Relay 3.573,0.74 4.031,0.938 0.458,0.198 10 false IG 1.479,8.417 3.333,8.635 1.854,0.219 10 false : CAN Communication Line 3.365,0.625 3.823,0.823 0.458,0.198 10 false 1 3.333,7.646 4.531,7.844 1.198,0.198 10 false D97 4.854,4.854 5.271,5.063 0.417,0.208 10 false 7 4.854,5.156 5.271,5.365 0.417,0.208 10 false 8 4.844,6.844 5.26,7.052 0.417,0.208 10 false 6 5.594,5.583 6.01,5.792 0.417,0.208 10 false A25 6.031,4.854 6.448,5.063 0.417,0.208 10 false 2 6.031,5.135 6.448,5.344 0.417,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The acoustic vehicle alerting system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the automatic high beam system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393

Result:
Result Proceed to
DTC B1350 is not output A
DTC B1350 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) 0 km/h (0 mph) vehicle proximity warning sound OFF or ON -
Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display
Proximity Sound (Vehicle Stationary)
50004 393 2

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B



A

B

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the D97 vehicle approaching speaker controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D97)Location & Routing

Click Connector(D97)Instrument Panel>Instrument Panel Wire>Vehicle Approaching Speaker Controller

D97-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR