Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37H0E _59 Vehicle Exterior _095212 WIPER / WASHER _0447384 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1373  Lost Communication with Wiper System LIN BUS  


DESCRIPTION

The main body ECU (multiplex network body ECU) communicates with the windshield wiper motor assembly, windshield wiper switch assembly and rain sensor via LIN communication. If a malfunction occurs in the LIN communication line and a communication error occurs, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1373 Lost Communication with Wiper System LIN BUS
DTC Detection Condition:

Ignition switch ON (IG+ voltage 9.5 V or higher)


Malfunction Status:

Wire-type LIN communication error detected


Malfunction Duration:

7 seconds or more


·

Windshield wiper motor assembly

·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body A

WIRING DIAGRAM

E381430E05
0.833,1.5 1.156,1.677 0.323,0.177 10 false A37 0.813,1.698 3.271,1.917 2.458,0.219 10 false Windshield Wiper Motor Assembly 2.031,0.875 2.365,1.042 0.333,0.167 10 false LIN 2.396,0.708 3.104,0.885 0.708,0.177 10 false 7*1, 6*2 5.271,0.719 5.469,0.885 0.198,0.167 10 false 3 5.5,0.875 5.927,1.042 0.427,0.167 10 false LIN3 5.115,1.479 5.438,1.656 0.323,0.177 10 false D12 5.115,1.656 6.771,2.01 1.656,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.26,3.115 5.458,3.281 0.198,0.167 10 false 3 5.5,3.271 5.927,3.438 0.427,0.167 10 false MPX 5.51,3.875 6.448,4.052 0.938,0.177 10 false H21 5.51,4.042 6.365,4.219 0.854,0.177 10 false Rain Sensor 0.688,4.229 2.625,4.406 1.938,0.177 10 false : LIN Communication Line 2.646,4.219 3.5,4.417 0.854,0.198 10 false *1: for LHD 3.646,4.208 4.5,4.406 0.854,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR THE DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B1373 is not output A
B1373 is output B



A

B

3.CHECK RAIN SENSOR (CLEAR THE DTCS)
3.CHECK RAIN SENSOR (CLEAR THE DTCS)

Pre-procedure1

a.

Disconnect the H21 rain sensor connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

4.CHECK RAIN SENSOR (CHECK FOR DTCS)
4.CHECK RAIN SENSOR (CHECK FOR DTCS)
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only B1279 is output A
B1373 is output B



A

B

5.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY (CLEAR THE DTCS)
5.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY (CLEAR THE DTCS)

Pre-procedure1

a.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

6.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
6.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only B1245 is output A
B1373 is output B



A

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)
7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - RAIN SENSOR)

Pre-procedure1

a.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H21 rain sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D12,H21)Location & Routing

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(H21)Body>No. 1 Roof Wire>Rain Sensor

D12-3 (LIN3) - H21-3 (MPX) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)

Pre-procedure1

a.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A37 windshield wiper motor assembly connector.


c.

Disconnect the H21 rain sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D12)Location & Routing

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

D12-3 (LIN3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR