Home › Audio / Visual / Telematics › AUDIO / VIDEO › ASC SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0447863 ASC SYSTEM J

AUDIO / VIDEO  ASC SYSTEM  Main Switch Circuit  


DESCRIPTION

The stereo component equalizer assembly detects ASC switch signals.

The ASC system can be turned on and off by operating the ASC switch (vehicle sound switch).

WIRING DIAGRAM

E450975E01
5.844,3.021 7.125,3.417 1.281,0.396 10 false Stereo Component Equalizer Assembly 5.854,2.844 6.313,3.042 0.458,0.198 10 false D104 2.688,2.74 5.281,2.938 2.594,0.198 10 false ASC Switch (Vehicle Sound Switch) 5.917,1.573 6.375,1.771 0.458,0.198 10 false IND 5.927,2.063 6.385,2.26 0.458,0.198 10 false SW 5.094,1.427 5.552,1.625 0.458,0.198 10 false IND 5.042,1.948 5.5,2.146 0.458,0.198 10 false ECU 5.75,1.427 5.906,1.625 0.156,0.198 10 false 7 5.75,1.958 5.906,2.156 0.156,0.198 10 false 5 5.448,1.417 5.604,1.615 0.156,0.198 10 false 4 5.427,1.948 5.667,2.146 0.24,0.198 10 false 2 2.74,1.948 3.198,2.146 0.458,0.198 10 false B 2.552,1.927 3.01,2.125 0.458,0.198 10 false 5 0.073,2.073 1.188,2.521 1.115,0.448 10 false from IG1 P NO. 1 Relay 1.563,2.24 2.406,2.573 0.844,0.333 10 false IG1 P NO.2 2.688,2.531 3.146,2.729 0.458,0.198 10 false D106

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > ASC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASC Switch ASC switch on/off status OFF or ON OFF: ASC switch (vehicle sound switch) off
ON: ASC switch (vehicle sound switch) on
-
Body Electrical > ASC > Data List
Tester Display
ASC Switch
50003 365 30
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ASC SWITCH (VEHICLE SOUND SWITCH)
2.INSPECT ASC SWITCH (VEHICLE SOUND SWITCH)

OK

3.CHECK HARNESS AND CONNECTOR (ASC SWITCH [VEHICLE SOUND SWITCH] - STEREO COMPONENT EQUALIZER ASSEMBLY)

NG

REPLACE ASC SWITCH (VEHICLE SOUND SWITCH)

3.CHECK HARNESS AND CONNECTOR (ASC SWITCH [VEHICLE SOUND SWITCH] - STEREO COMPONENT EQUALIZER ASSEMBLY)
a.

Disconnect the D106 ASC switch (vehicle sound switch) connector.


b.

Disconnect the D104 stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D106,D104)Location & Routing

Click Connector(D106)Instrument Panel>Instrument Panel Wire>Vehicle Sound Switch

Click Connector(D104)Instrument Panel>Instrument Panel Wire>Stereo Component Equalizer Assembly

D106-4(IND) - D104-7(IND) Always Below 1 Ω
D106-2(ECU) - D104-5(SW) Always Below 1 Ω
D106-4(IND) or D104-7(IND) - Body ground Always 10 kΩ or higher
D106-2(ECU) or D104-5(SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR