Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0447864 TOYOTA MULTI OPERATION TOUCH SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  B1522  Lost Communication with DCU Video Line Signal  


DESCRIPTION

The radio receiver assembly and integration control sub-assembly are connected via video signal (digital) lines.

This DTC is stored when a video signal (digital) line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1522 Lost Communication with DCU Video Line Signal GVIF disconnected (from radio receiver assembly to integration control sub-assembly)
·

Harness or connector (GVIF cable)

·

Integration control sub-assembly

·

Radio receiver assembly


D-SEAT SW A

WIRING DIAGRAM

E453340E07
5.156,2.406 6.615,2.854 1.458,0.448 10 false Integration Control Sub-assembly 0.719,2.385 2.656,2.677 1.938,0.292 10 false Radio Receiver Assembly 0.74,2.177 1.219,2.354 0.479,0.177 10 false D143 5.146,2.24 5.552,2.438 0.406,0.198 10 false D144 5.385,0.667 5.792,0.844 0.406,0.177 10 false GV+ 5.396,1.229 5.802,1.406 0.406,0.177 10 false GV- 5.385,1.792 5.792,1.969 0.406,0.177 10 false GVG 1.458,0.656 1.896,0.833 0.438,0.177 10 false GVI+ 1.49,1.219 1.896,1.396 0.406,0.177 10 false GVI- 1.406,1.792 1.813,1.969 0.406,0.177 10 false GVG1 3.531,1.604 3.677,1.792 0.146,0.188 10 false * 0.594,3.427 1.688,3.656 1.094,0.229 10 false : GVIF Cable 0.208,3.135 2.115,3.302 1.906,0.167 10 false *: Shielded 5.188,0.531 5.375,0.708 0.188,0.177 10 false 1 5.177,1.094 5.365,1.271 0.188,0.177 10 false 2 5.177,1.688 5.365,1.865 0.188,0.177 10 false 3 1.885,0.531 2.073,0.708 0.188,0.177 10 false 2 1.885,1.115 2.073,1.292 0.188,0.177 10 false 1 1.885,1.677 2.073,1.854 0.188,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the integration control sub-assembly, always replace it with a new one. If a integration control sub-assembly which was installed to another vehicle is used, the following may occur:

·

A communication malfunction DTC may be stored.

·

The integration control sub-assembly may not operate normally.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)

Pre-procedure1

a.
E365509C80
1.469,0.531 1.875,0.865 0.406,0.333 1.448,2.698 1.854,3.031 0.406,0.333 0.969,1.25 1.115,1.25 1.115,1.25 1.521,1.469 true 1.813,1.469 2.156,1.281 2.156,1.281 2.313,1.281 true 1.698,1.76 2.031,2.26 2.031,2.26 2.188,2.26 true 1.688,3.906 2.021,4.406 2.021,4.406 2.177,4.406 true 1.823,3.583 2.167,3.396 2.167,3.396 2.323,3.396 true 0.979,3.375 1.125,3.375 1.125,3.375 1.531,3.594 true 0.052,0.146 0.365,0.344 0.313,0.198 10 false *a 0.073,2.573 0.385,2.771 0.313,0.198 10 false *b 1.51,2.792 1.969,2.99 0.458,0.198 10 false D144 1.521,0.625 1.979,0.823 0.458,0.198 10 false D143 2.344,1.198 2.771,1.406 0.427,0.208 10 false GVI+ 0.552,1.188 0.979,1.396 0.427,0.208 10 false GVI- 2.25,2.198 2.677,2.406 0.427,0.208 10 false GVG1 0.563,3.313 0.99,3.521 0.427,0.208 10 false GV+ 2.375,3.333 2.802,3.542 0.427,0.208 10 false GV- 2.24,4.344 2.667,4.552 0.427,0.208 10 false GVG
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to Integration Control Sub-assembly)


Disconnect the D143 radio receiver assembly connector.


b.

Disconnect the D144 integration control sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D143,D144)Location & Routing

Click Connector(D143)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D144)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D143-2 (GVI+) - D144-1 (GV+) Always Below 1 Ω
D143-1 (GVI-) - D144-2 (GV-) Always Below 1 Ω
D143-3 (GVG1) - D144-3 (GVG) Always Below 1 Ω
D143-2 (GVI+) or D144-1 (GV+) - Body ground Always 10 kΩ or higher
D143-1 (GVI-) or D144-2 (GV-) - Body ground Always 10 kΩ or higher
D143-3 (GVG1) or D144-3 (GVG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

Pre-procedure1

a.

Replace the integration control sub-assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL



b.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO RECEIVER ASSEMBLY