Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0447864 TOYOTA MULTI OPERATION TOUCH SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  B1523  DCU GVIF Disconnected (from D-SEAT SW to Multi Display)  


DESCRIPTION

The integration control sub-assembly and multi-display assembly are connected via video signal (digital) lines.

This DTC is stored when a video signal (digital) line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1523 DCU GVIF Disconnected (from D-SEAT SW to Multi Display) GVIF disconnected (from integration control sub-assembly to multi-display assembly)
·

Harness or connector (GVIF cable)

·

Multi-display assembly

·

Integration control sub-assembly


D-SEAT SW A

WIRING DIAGRAM

E393807E11
5.125,2.344 6.844,2.958 1.719,0.615 10 false Integration Control Sub-assembly 0.542,2.313 2.552,2.531 2.01,0.219 10 false Multi-display Assembly 0.542,2.167 2.448,2.333 1.906,0.167 10 false D148 5.135,2.198 5.521,2.354 0.385,0.156 10 false D158 5.333,0.667 5.833,0.844 0.5,0.177 10 false GV+ 5.323,1.25 5.729,1.427 0.406,0.177 10 false GV- 5.344,1.802 5.75,1.979 0.406,0.177 10 false GVG 1.365,0.677 1.802,0.854 0.438,0.177 10 false GV+ 1.365,1.26 1.771,1.438 0.406,0.177 10 false GV- 1.375,1.792 1.781,1.969 0.406,0.177 10 false GVG 3.479,1.781 3.625,1.969 0.146,0.188 10 false * 0.708,3.438 2.615,3.604 1.906,0.167 10 false : GVIF Cable 0.323,3.063 2.229,3.229 1.906,0.167 10 false *: Shielded 5.073,0.521 5.26,0.698 0.188,0.177 10 false 1 5.073,1.094 5.26,1.271 0.188,0.177 10 false 2 5.083,1.667 5.271,1.844 0.188,0.177 10 false 3 1.865,0.531 2.052,0.708 0.188,0.177 10 false 1 1.865,1.115 2.052,1.292 0.188,0.177 10 false 2 1.865,1.677 2.052,1.854 0.188,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the integration control sub-assembly, always replace it with a new one. If a integration control sub-assembly which was installed to another vehicle is used, the following may occur:

·

A communication malfunction DTC may be stored.

·

The integration control sub-assembly may not operate normally.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

Pre-procedure1

a.
E397412C06
1.458,0.625 1.917,0.875 0.458,0.25 1.469,2.792 1.927,3.042 0.458,0.25 1.521,1.438 1.146,1.146 1.146,1.146 0.979,1.146 true 1.823,1.438 2.083,1.188 2.083,1.188 2.229,1.188 true 1.719,1.823 2.198,2.188 2.198,2.188 2.344,2.188 true 1.51,3.594 1.135,3.302 1.135,3.302 0.969,3.302 true 1.833,3.604 2.146,3.313 2.146,3.313 2.292,3.313 true 1.677,3.938 2.156,4.302 2.156,4.302 2.302,4.302 true 1.531,0.698 2.146,0.896 0.615,0.198 10 false D148 1.552,2.865 2.167,3.063 0.615,0.198 10 false D158 0.344,0.313 0.958,0.51 0.615,0.198 10 false *a 0.417,2.479 1.031,2.677 0.615,0.198 10 false *b 0.573,1.083 1.188,1.281 0.615,0.198 10 false GV+ 2.271,1.125 2.885,1.323 0.615,0.198 10 false GV- 2.406,2.125 3.021,2.323 0.615,0.198 10 false GVG 0.583,3.229 1.198,3.427 0.615,0.198 10 false GV+ 2.375,3.25 2.99,3.448 0.615,0.198 10 false GV- 2.375,4.219 2.99,4.417 0.615,0.198 10 false GVG
*a Front view of wire harness connector
(to Multi-display Assembly)
*b Front view of wire harness connector
(to Integration Control Sub-assembly)


Disconnect the D148 multi-display assembly connector.


b.

Disconnect the D158 integration control sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D148,D158)Location & Routing

Click Connector(D148)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

Click Connector(D158)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D148-1 (GV+) - D158-1 (GV+) Always Below 1 Ω
D148-2 (GV-) - D158-2 (GV-) Always Below 1 Ω
D148-3 (GVG) - D158-3 (GVG) Always Below 1 Ω
D148-1 (GV+) - D158-1 (GV+) - Body ground Always 10 kΩ or higher
D148-2 (GV-) or D158-2 (GV-) - Body ground Always 10 kΩ or higher
D148-3 (GVG) or D158-3 (GVG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

Pre-procedure1

a.

Replace the integration control sub-assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL



b.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

Procedure1

a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

B