Home › General › MAINTENANCE › AUXILIARY BATTERY
RM37H0E _V1 General _095083 MAINTENANCE _0454374 AUXILIARY BATTERY A

MAINTENANCE  AUXILIARY BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A478432N01
4.458,0.958 4.99,0.958 false 5.385,2.323 5.75,2.323 false 4.458,3.521 4.667,3.521 4.667,3.521 4.938,4.208 true 5.802,4 5.802,3.656 false 6.438,0.25 6.781,0.25 false 5.51,3.083 5.875,3.083 false 6.146,3.51 6.51,3.51 false 4.073,4.906 4.927,4.906 true 3.073,4.073 3.927,4.073 true 6.281,0.104 6.563,0.458 0.281,0.354 18 false 1 4.26,0.813 4.542,1.167 0.281,0.354 18 false 2 4.281,3.385 4.563,3.74 0.281,0.354 18 false 3 6.573,3.365 6.854,3.719 0.281,0.354 18 false 4 5.802,2.167 6.083,2.521 0.281,0.354 18 false 5 5.74,4 6.021,4.354 0.281,0.354 18 false 6 3.885,4.771 4.167,5.125 0.281,0.354 18 false 8 5.333,3 5.646,3.198 0.313,0.198 10 false *1 2.885,3.917 3.167,4.271 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 LUGGAGE TRIM SERVICE HOLE COVER 64718B - - -
3 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 POSITIVE AUXILIARY BATTERY TERMINAL - - - -
5 BATTERY CLAMP 74481A - - -
6 BATTERY HOLD DOWN CLAMP SUB-ASSEMBLY 74406B - - -
7 BATTERY HOSE 28885B - - -
8 AUXILIARY BATTERY - - - -

*1 BATTERY TERMINAL CONNECTOR COVER - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during auxiliary battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
Air Conditioning System After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)

·

When replacing the auxiliary battery, use a new auxiliary battery of the same dimensions and same capacity or more from the same class at a 20-hour rate.

·

After replacing the auxiliary battery, install the ventilation hole plug supplied with the new auxiliary battery or the ventilation hole plug from the old auxiliary battery to the ventilation hole on the side to which the battery hose is not connected.




Hide 64718B 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

a.
A478433


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

a.
A478434


Hide 4.DISCONNECT CABLE FROM POSITIVE AUXILIARY BATTERY TERMINAL

a.
A478435


Hide 74481A 5.REMOVE BATTERY CLAMP

a.
A478436


Hide 74406B 6.DISCONNECT BATTERY HOLD DOWN CLAMP SUB-ASSEMBLY

a.
A478437


Hide 28885B 7.DISCONNECT BATTERY HOSE

a.
A480711


Hide 8.REMOVE AUXILIARY BATTERY

a.
A478438