Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0447865 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157011  Indicator (Red) Circuit Short to Ground  B157013  Indicator (Red) Circuit Open  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch red indicator circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch red If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157011 Indicator (Red) Circuit Short to Ground Manual (SOS) switch red indicator impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly (manual [SOS] switch)

·

Harness or connector


Telematics A
B157013 Indicator (Red) Circuit Open Manual (SOS) switch red indicator impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly (manual [SOS] switch)

·

Harness or connector


Telematics A

WIRING DIAGRAM

E354565E66
1.281,0.979 1.74,1.177 0.458,0.198 10 false RED 2.469,0.563 3.083,0.76 0.615,0.198 10 false IND1 2.417,1.146 3.031,1.344 0.615,0.198 10 false GND3 0.323,2.24 3.406,2.531 3.083,0.292 10 false Map Light Assembly (Manual [SOS] Switch) 4.906,0.583 5.219,0.781 0.313,0.198 10 false 4 4.917,1.146 5.229,1.344 0.313,0.198 10 false 3 5.198,0.75 5.813,0.948 0.615,0.198 10 false IND1 5.188,1.167 5.802,1.365 0.615,0.198 10 false SIG- 4.906,2.052 5.365,2.25 0.458,0.198 10 false D68 4.906,2.219 7.115,2.594 2.208,0.375 10 false Telematics Transceiver 2.969,0.604 3.385,0.917 0.417,0.313 10 false 6 2.969,1.156 3.417,1.51 0.448,0.354 10 false 9 0.344,2.063 0.802,2.26 0.458,0.198 10 false H10

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



HINT:

If DTC B157011 or B157013 is stored, the manual (SOS) switch red indicator may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH) (RED INDICATOR)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH) (RED INDICATOR)

Pre-procedure1

a.
E427070C20
1.635,1.01 1.875,0.281 1.875,0.281 2,0.281 true 1.063,0.99 0.938,0.292 0.938,0.292 0.76,0.292 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 0.333,0.219 0.854,0.438 0.521,0.219 10 false GND3 2.083,0.219 2.521,0.427 0.438,0.208 10 false IND1
*a Component without harness connected
(Map Light Assembly [Manual (SOS) Switch])


Remove the map light assembly (manual [SOS] switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 6 (IND1) and a negative (-) lead to terminal 9 (GND3) of the map light assembly (manual [SOS] switch) connector.


Procedure1

a.

Check if the manual (SOS) switch red indicator illuminates.

OK:

Manual (SOS) switch red indicator illuminates.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY [MANUAL (SOS) SWITCH])

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY [MANUAL (SOS) SWITCH])

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the H10 map light assembly (manual [SOS] switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,H10)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

D68-4 (IND1) - H10-6 (IND1) Always Below 1 Ω
D68-3 (SIG-) - H10-9 (GND3) Always Below 1 Ω
D68-4 (IND1) or H10-6 (IND1) - Body ground Always 10 kΩ or higher
D68-3 (SIG-) or H10-9 (GND3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT