This DTC is stored when the telematics transceiver detects an open or short circuit in the manual (SOS) switch.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C511 | Emergency Call Switch Circuit Short to Ground | Manual (SOS) switch impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
| B15C513 | Emergency Call Switch Circuit Open | Manual (SOS) switch impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual [SOS] switch) ·
Harness or connector |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Remove the map light assembly (manual [SOS] switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
| *a | Component without harness connected
(Map Light Assembly [Manual (SOS) Switch]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SIG1) - 9 (GND3) | Manual (SOS) switch not operated | 410 to 414 Ω |
| 13 (SIG1) - 9 (GND3) | Manual (SOS) switch operated | 81 to 83 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the D68 telematics transceiver connector.
Disconnect the H10 map light assembly (manual [SOS] switch) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D68,H10)Location & Routingewd_type=routing;type=c,c;code=D68,H10 Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiverewd_type=component;type=c;code=D68;pinno=21,3 Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=H10;pinno=13,9 |
||
| D68-21 (SIG1) - H10-13 (SIG1) | Always | Below 1 Ω |
| D68-3 (SIG-) - H10-9 (GND3) | Always | Below 1 Ω |
| D68-21 (SIG1) - Body ground | Always | 10 kΩ or higher |
| D68-3 (SIG-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT