Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear)
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0454705 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B611717N16
3.313,1.958 3.583,2.292 3.583,2.292 3.969,2.292 false 4.021,2.125 4.573,2.479 0.552,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ULTRASONIC SENSOR CUSHION SET 89305 - - -

B601965N02
2,1.927 3.25,2.667 1.25,0.74 4.771,1.25 6.104,2 1.333,0.75 0.365,0.74 1.229,1.385 0.865,0.646 3.198,0.052 4.063,0.698 0.865,0.646 0.583,1.25 0.75,1 0.75,1 0.917,1 false 3.813,2.938 3.813,3.188 3.813,3.188 3.896,3.188 false 3.385,0.51 3.552,0.26 3.552,0.26 3.719,0.26 false 5.125,1.781 5.188,1.531 5.188,1.531 5.292,1.531 false 2.313,2.479 2.479,2.229 2.479,2.229 2.563,2.229 false 3.396,0.885 3.729,0.885 false 2.854,1.396 3.188,1.396 false 2.073,1.625 2.406,1.625 false 1.219,1.49 1.552,1.49 false 2.917,2.813 2.917,3.063 2.917,3.063 2.833,3.063 false 5.156,2.198 5.156,2.281 5.156,2.281 5.406,2.281 false 4.604,2.74 4.604,2.823 4.604,2.823 4.854,2.823 false 3.406,4.167 3.74,4.167 false 6.458,0.229 6.792,0.229 false 2.469,1.5 2.75,1.854 0.281,0.354 18 false 7 3.25,4.042 3.531,4.396 0.281,0.354 18 false 8 3.25,1.26 3.531,1.615 0.281,0.354 18 false 7 3.781,0.75 4.063,1.104 0.281,0.354 18 false 6 0.979,0.885 1.26,1.24 0.281,0.354 18 false 5 3.781,0.146 4.063,0.5 0.281,0.354 18 false 5 1.615,1.354 1.896,1.708 0.281,0.354 18 false 6 2.906,2.125 3.25,2.427 0.344,0.302 10 false ● 2.521,2.99 2.865,3.292 0.344,0.302 10 false ● 4.26,3.094 4.604,3.396 0.344,0.302 10 false ● 5.229,2.719 5.573,3.021 0.344,0.302 10 false ● 5.729,2.208 6.073,2.51 0.344,0.302 10 false ● 5.635,1.448 5.979,1.75 0.344,0.302 10 false ● 3.01,2.083 3.292,2.438 0.281,0.354 18 false 2 4.396,3.073 4.677,3.427 0.281,0.354 18 false 4 5.344,2.688 5.625,3.042 0.281,0.354 18 false 4 2.646,2.927 2.927,3.281 0.281,0.354 18 false 3 5.854,2.177 6.135,2.531 0.281,0.354 18 false 3 5.76,1.396 6.042,1.75 0.281,0.354 18 false 2 2.104,1.979 2.479,2.219 0.375,0.24 12 false *A 3.26,0.083 3.635,0.323 0.375,0.24 12 false *A 0.438,0.781 0.813,1.021 0.375,0.24 12 false *A 4.865,1.292 5.24,1.531 0.375,0.24 12 false *A 6.271,0.104 6.552,0.458 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

2 REAR SIDE ULTRASONIC SENSOR RETAINER 89C48C (Click here) - -
3 REAR CORNER ULTRASONIC SENSOR RETAINER 89C48A (Click here) - -
4 REAR CENTER ULTRASONIC SENSOR RETAINER 89C48B (Click here) - -
5 REAR SIDE ULTRASONIC SENSOR 89342B - - -
6 REAR CORNER ULTRASONIC SENSOR 89342 - - -
7 REAR CENTER ULTRASONIC SENSOR 89342A - - -
8 REAR BUMPER ASSEMBLY - - - -
9 PERFORM CALIBRATION - - - (Click here)

*A w/ Advanced Park - -
● Non-reusable part - -

PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET

Hide 89C48C 2.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park)

a.
B599557C02
2.76,2.521 2.927,2.688 2.927,2.688 3.177,2.688 false 0.417,0.292 0.698,0.646 0.281,0.354 18 false i 4.042,0.302 4.323,0.656 0.281,0.354 18 false ii 0.406,1.781 0.688,2.135 0.281,0.354 18 false iii 0.427,3.167 0.708,3.521 0.281,0.354 18 false iv 6.021,0.333 6.333,0.531 0.313,0.198 10 false *a 6.656,0.938 6.969,1.135 0.313,0.198 10 false *a 3.229,2.625 3.542,2.823 0.313,0.198 10 false *b 0.406,4.677 0.688,5.031 0.281,0.354 18 false v
*a 30 mm (1.18 in.) *b Mark-off Line
V100144

Installation area - -


i.

Clean the rear bumper assembly surface:

1. When reusing the rear bumper assembly, remove remaining double-sided tape from the rear bumper assembly.

2. Using a heat light, heat the rear bumper assembly surface.

Standard Value:
Part Temperature
Rear Bumper Assembly 20 to 30°C (68 to 86°F)
Rear Side Ultrasonic Sensor Retainer 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


3. Remove any remaining double-sided tape from the rear bumper assembly and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rear side ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper assembly surface.




ii.

Cover the sensor installation hole from the outside of the bumper with a 30 mm (1.18 in.) square piece of tape.


iii.

Primer application:

1. Apply primer to the rear bumper assembly on the installation area of the rear side ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear side ultrasonic sensor retainer has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the rear bumper assembly and a new rear side ultrasonic sensor retainer.

NOTICE:

Do not heat the rear side ultrasonic sensor retainer and rear bumper assembly excessively.



v.

Install the rear side ultrasonic sensor retainer in the position shown in the illustration.

NOTICE:

The application strength of the rear side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear bumper assembly.




b.

The orientation for the RH side is the opposite of the LH side.


Hide 89C48A 3.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

a.
B599556C02
2.76,2.521 2.927,2.688 2.927,2.688 3.177,2.688 false 0.417,0.292 0.698,0.646 0.281,0.354 18 false i 4.042,0.302 4.323,0.656 0.281,0.354 18 false ii 0.406,1.781 0.688,2.135 0.281,0.354 18 false iii 0.427,3.167 0.708,3.521 0.281,0.354 18 false iv 6.021,0.333 6.333,0.531 0.313,0.198 10 false *a 6.656,0.938 6.969,1.135 0.313,0.198 10 false *a 3.229,2.625 3.542,2.823 0.313,0.198 10 false *b 0.406,4.677 0.688,5.031 0.281,0.354 18 false v
*a 30 mm (1.18 in.) *b Mark-off Line
V100144

Installation area - -


i.

Clean the rear bumper assembly surface:

1. When reusing the rear bumper assembly, remove remaining double-sided tape from the rear bumper assembly.

2. Using a heat light, heat the rear bumper assembly surface.

Standard Value:
Part Temperature
Rear Bumper Assembly 20 to 30°C (68 to 86°F)
Rear Corner Ultrasonic Sensor Retainer 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


3. Remove any remaining double-sided tape from the rear bumper assembly and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rear corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper assembly surface.




ii.

Cover the sensor installation hole from the outside of the bumper with a 30 mm (1.18 in.) square piece of tape.


iii.

Primer application:

1. Apply primer to the rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the rear bumper assembly and a new rear corner ultrasonic sensor retainer.

NOTICE:

Do not heat the rear corner ultrasonic sensor retainer and rear bumper assembly excessively.



v.

Install the rear corner ultrasonic sensor retainer in the position shown in the illustration.

NOTICE:

The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear bumper assembly.




b.

The orientation for the RH side is the opposite of the LH side.


Hide 89C48B 4.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

a.
B599555C02
2.76,2.521 2.927,2.688 2.927,2.688 3.177,2.688 false 0.417,0.292 0.698,0.646 0.281,0.354 18 false i 4.042,0.302 4.323,0.656 0.281,0.354 18 false ii 0.406,1.781 0.688,2.135 0.281,0.354 18 false iii 0.427,3.167 0.708,3.521 0.281,0.354 18 false iv 6.021,0.333 6.333,0.531 0.313,0.198 10 false *a 6.656,0.938 6.969,1.135 0.313,0.198 10 false *a 3.229,2.625 3.542,2.823 0.313,0.198 10 false *b 0.406,4.677 0.688,5.031 0.281,0.354 18 false v
*a 30 mm (1.18 in.) *b Mark-off Line
V100144

Installation area - -


i.

Clean the rear bumper assembly surface:

1. When reusing the rear bumper assembly, remove remaining double-sided tape from the rear bumper assembly.

2. Using a heat light, heat the rear bumper assembly surface.

Standard Value:
Part Temperature
Rear Bumper Assembly 20 to 30°C (68 to 86°F)
Rear Center Ultrasonic Sensor Retainer 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly excessively.


3. Remove any remaining double-sided tape from the rear bumper assembly and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the rear center ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new rear bumper assembly surface.




ii.

Cover the sensor installation hole from the outside of the bumper with a 30 mm (1.18 in.) square piece of tape.


iii.

Primer application:

1. Apply primer to the rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the rear bumper assembly and a new rear center ultrasonic sensor retainer.

NOTICE:

Do not heat the rear center ultrasonic sensor retainer and rear bumper assembly excessively.



v.

Install the rear center ultrasonic sensor retainer in the position shown in the illustration.

NOTICE:

The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rear bumper assembly.




b.

The orientation for the RH side is the opposite of the LH side.


Hide 89342B 5.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Advanced Park)

Hide 89342 6.INSTALL REAR CORNER ULTRASONIC SENSOR

Hide 89342A 7.INSTALL REAR CENTER ULTRASONIC SENSOR

Hide 8.INSTALL REAR BUMPER ASSEMBLY