Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio receiver assembly

·

Harness or connector

·

No. 2 junction connector


Navigation System A
B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Headup display (meter mirror sub-assembly) power source circuit

·

Headup display (meter mirror sub-assembly)

·

Radio receiver assembly

·

Harness or connector

·

No. 2 junction connector


Navigation System A

*: w/ Headup Display System


HINT:

The radio receiver assembly is the master unit.


WIRING DIAGRAM

E436805E25
2.906,2.177 4.083,2.563 1.177,0.385 10 false Combination Meter Assembly 2.906,2 3.354,2.292 0.448,0.292 10 false D41 3.698,1.656 4.146,1.948 0.448,0.292 10 false ES 3.083,1.063 3.531,1.354 0.448,0.292 10 false B 3.104,1.521 3.552,1.813 0.448,0.292 10 false IG+ 2.813,0.979 3.26,1.271 0.448,0.292 10 false 22 2.823,1.406 3.271,1.698 0.448,0.292 10 false 21 4.01,1.229 4.458,1.521 0.448,0.292 10 false 7 4.01,0.938 4.458,1.229 0.448,0.292 10 false 8 3.99,1.531 4.438,1.823 0.448,0.292 10 false 31 4.323,0.938 4.771,1.229 0.448,0.292 10 false 14 4.344,1.229 4.792,1.521 0.448,0.292 10 false 3 5.531,0.927 5.979,1.219 0.448,0.292 10 false 13 5.531,1.24 5.979,1.531 0.448,0.292 10 false 2 5.927,0.938 6.375,1.229 0.448,0.292 10 false 5 6.052,1.896 7,2.406 0.948,0.51 10 false Radio Receiver Assembly 5.927,1.229 6.375,1.521 0.448,0.292 10 false 6 6.052,1.719 7,2.281 0.948,0.563 10 false D64 6.125,1.073 6.656,1.354 0.531,0.281 10 false CNH1 6.125,1.365 6.677,1.656 0.552,0.292 10 false CNL1 0.24,1.052 2.198,1.406 1.958,0.354 10 false from Auxiliary Battery 0.51,1.479 2.469,1.833 1.958,0.354 10 false from IG2 D Relay 2.083,1.208 3.229,1.542 1.146,0.333 10 false METER 1.948,1.677 2.802,2.021 0.854,0.344 10 false IG2 D NO.1 2.844,4.188 4.302,4.792 1.458,0.604 10 false Headup Display (Meter Mirror Sub-assembly)* 2.833,4.031 3.781,4.427 0.948,0.396 10 false D95 1.844,3.083 3.208,3.427 1.365,0.344 10 false MPX-B D NO.1 1.99,3.771 3.948,4.125 1.958,0.354 10 false IG1 D NO.1 0.177,3.615 2.156,4.083 1.979,0.469 10 false from IG1 D NO.1 Relay 4.438,4.771 6.781,5.052 2.344,0.281 10 false No. 2 Junction Connector 4.438,4.594 6.396,4.948 1.958,0.354 10 false D167 3.094,2.938 3.542,3.229 0.448,0.292 10 false B 3.073,3.635 3.521,3.927 0.448,0.292 10 false IG 3.688,3.458 4.135,3.75 0.448,0.292 10 false ES 3.667,2.896 4.115,3.188 0.448,0.292 10 false TX+ 3.688,3.188 4.146,3.594 0.458,0.406 10 false TX- 3.969,2.781 4.417,3.073 0.448,0.292 10 false 14 3.969,3.063 4.417,3.354 0.448,0.292 10 false 15 4.313,2.781 4.76,3.073 0.448,0.292 10 false 12 4.365,3.063 4.813,3.354 0.448,0.292 10 false 1 3.99,3.344 4.438,3.635 0.448,0.292 10 false 4 2.854,2.792 3.302,3.083 0.448,0.292 10 false 2 2.854,3.49 3.302,3.781 0.448,0.292 10 false 1 1.021,5.031 3.625,5.406 2.604,0.375 10 false : Local Bus Communication Line 3.635,1.073 4.146,1.313 0.51,0.24 10 false TX+ 0.365,4.542 2.552,4.948 2.188,0.406 10 false *: w/ Headup Display System 0.229,2.906 2.188,3.26 1.958,0.354 10 false from Auxiliary Battery 3.646,1.333 4.156,1.573 0.51,0.24 10 false TX-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:

B1324 and B1325 will not continue to output when clear DTC is performed even if the malfunction continues.


PROCEDURE

1.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
B1324 and B1325 are not output A
B1324 and B1325 are output B
Only B1324 is output C
Only B1325 is output D



A

B

2.CHECK LOCAL BUS

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

14.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
2.CHECK LOCAL BUS

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Result Proceed to
D167-13 - D167-2 is less than or equal to 54 Ω A
D167-13 - D167-2 is more than or equal to 70 Ω B
None of the above conditions are met C



Post-procedure1

c.

None



A

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

B

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

C

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D95 headup display (meter mirror sub-assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-14 (TX+) - D95-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D41 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-8 (TX+) - D41-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D64 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-5 (CNH1) - D64-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D64 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-5 (CNH1) - D64-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the D41 combination meter assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-31 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-22 (B) - Body ground Ignition switch off 11 to 14 V
D41-21 (IG+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D41 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-8 (TX+) - D41-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)

Pre-procedure1

a.

Disconnect the D95 headup display (meter mirror sub-assembly) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-2 (B) - Body ground Ignition switch off 11 to 14 V
D95-1 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

15.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-12 - D167-1 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

18.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)
16.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

17.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
17.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D64 radio receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-5 (CNH1) - D64-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D95 headup display (meter mirror sub-assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-14 (TX+) - D95-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR