Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D0  MOST Communication Malfunction  


DESCRIPTION

Navigation system components communicate with each other via MOST communication.

If a line short or short to ground occurs in a MOST communication line, communication will not be possible and the navigation system will not operate normally.

After the ignition switch is turned to ACC, if the MOST communication network cannot be established and MOST communication is determined to not be possible, this DTC will be stored.

HINT:

Electrical noise may cause communication malfunctions between devices in the MOST network.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D0 MOST Communication Malfunction MOST network cannot be established.
·

Stereo component amplifier assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System B

WIRING DIAGRAM

E362100E07
1.135,0.729 1.594,0.927 0.458,0.198 10 false MO+ 1.177,1.146 1.635,1.344 0.458,0.198 10 false MO- 1.052,1.49 1.51,1.688 0.458,0.198 10 false SLDO 5.813,0.354 6.271,0.552 0.458,0.198 10 false WUO 1.208,2.031 1.667,2.229 0.458,0.198 10 false MI+ 1.229,2.406 1.688,2.604 0.458,0.198 10 false MI- 1.115,2.813 1.573,3.01 0.458,0.198 10 false SLDI 5.813,0.75 6.271,0.948 0.458,0.198 10 false MI+ 5.823,1.104 6.281,1.302 0.458,0.198 10 false MI- 5.823,2.823 6.281,3.021 0.458,0.198 10 false SLDO 5.823,1.49 6.281,1.688 0.458,0.198 10 false SLDI 1.167,0.375 1.625,0.573 0.458,0.198 10 false WUI 5.813,2.042 6.271,2.24 0.458,0.198 10 false MO+ 5.813,2.406 6.271,2.604 0.458,0.198 10 false MO- 5.438,3.438 5.896,3.635 0.458,0.198 10 false D142 0.229,3.406 0.688,3.604 0.458,0.198 10 false G111 5.438,3.604 7.115,3.854 1.677,0.25 10 false Radio Receiver Assembly 0.219,3.573 2.604,3.906 2.385,0.333 10 false Stereo Component Amplifier Assembly 1.594,1.396 1.771,1.615 0.177,0.219 10 false 7 1.583,1.927 1.76,2.146 0.177,0.219 10 false 2 1.573,2.292 1.75,2.51 0.177,0.219 10 false 3 1.583,2.677 1.76,2.896 0.177,0.219 10 false 4 1.594,0.604 1.771,0.823 0.177,0.219 10 false 5 1.594,0.99 1.771,1.208 0.177,0.219 10 false 6 1.583,0.26 1.76,0.479 0.177,0.219 10 false 8 5.563,0.219 5.74,0.438 0.177,0.219 10 false 1 5.563,0.969 5.74,1.188 0.177,0.219 10 false 3 5.552,1.365 5.729,1.583 0.177,0.219 10 false 4 5.573,0.604 5.75,0.823 0.177,0.219 10 false 2 5.531,1.917 5.708,2.135 0.177,0.219 10 false 5 5.542,2.292 5.719,2.51 0.177,0.219 10 false 6 5.542,2.698 5.719,2.917 0.177,0.219 10 false 7 3.563,1.427 4.271,1.635 0.708,0.208 10 false * 3.563,2.708 4.281,2.969 0.719,0.26 10 false * 0.833,4.073 2.74,4.302 1.906,0.229 10 false : MOST Communication Line 0.333,4.438 1.313,4.677 0.979,0.24 10 false *: Shielded

CHECK POINT

·

Before proceeding with the following procedure, start diagnostic mode, enter the "MOST Line Check" screen and check the results.

·

The following MOST line check result pattern table can be used to quickly identify trouble areas and inspection procedures.


MOST Network Outline
E391237E02
1.427,0.292 1.583,0.49 0.156,0.198 10 false c 3.531,0.448 3.688,0.646 0.156,0.198 10 false a 3.531,0.688 3.688,0.885 0.156,0.198 10 false b 1.156,0.927 3.542,1.49 2.385,0.563 10 false Stereo Component Amplifier Assembly 4.563,0.958 6.167,1.406 1.604,0.448 10 false Radio Receiver Assembly 0.844,2.115 3.063,2.333 2.219,0.219 10 false : Most Communication Line 0.844,2.458 2.5,2.656 1.656,0.198 10 false : Wake-up Signal 1.167,1.104 1.719,1.521 0.552,0.417 10 false (AMP) 4.563,1.146 5.146,1.396 0.583,0.25 10 false (DCU)

MOST Line Check Result Pattern
Pattern Device Name Result Trouble Area Inspection
1 DCU OK a, c Inspect MOST communication line between "DCU" and "AMP"
AMP OK
2 DCU OK b, c Inspect wake up communication line between "DCU" and "AMP"
AMP NCON

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
B15C3 and B15D3 are not output A
B15C3 is output B
B15D3 is output C


HINT:
·

If a short occurs in a speaker circuit, the sound output from the speakers will become very low or will stop and DTC B15C3 will be stored.

In this case, if the audio system volume is increased, current in the speaker circuit will increase more than necessary.

To prevent the current from becoming excessively high, when it increases to a certain amount, operation of the stereo component amplifier assembly will be suspended.

If operation is suspended, MOST communication will become impossible, the navigation system will not operate normally and DTC B15D0 will be stored.


·

If DTC B15C3 and B15D3 are output at the same time, perform troubleshooting for DTC B15C3 first.




A

2.PERFORM MOST LINE CHECK

B

C

2.PERFORM MOST LINE CHECK
a.
E323023C01
0.313,0.604 0.51,0.604 false 0.76,1.75 0.76,0.781 false 1.135,1.75 1.135,0.781 false 0.146,0.51 0.365,0.708 0.219,0.198 10 false *a 0.677,1.781 0.896,1.979 0.219,0.198 10 false *b 1.052,1.771 1.271,1.969 0.219,0.198 10 false *c
*a MOST Network Device Node Position Number
*b Device Name
*c Result


Enter the "MOST Line Check" screen. Refer to Check DTC (Check Using System Check Mode Screen) in DTC Check / Clear.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR


HINT:

"MOST" is displayed on "System Check Mode" screen when the MOST network is malfunctioning.


Result:
Result Proceed to
"OK" is displayed for all items. A
"NCON" is displayed for "AMP". B




A

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D142 radio receiver assembly connector.


b.

Disconnect the G111 stereo component amplifier assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D142,G111)Location & Routing

Click Connector(D142)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(G111)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assembly

D142-2 (MI+) - G111-5 (MO+) Always Below 1 Ω
D142-3 (MI-) - G111-6 (MO-) Always Below 1 Ω
D142-4 (SLDI) - G111-7 (SLDO) Always Below 1 Ω
D142-5 (MO+) - G111-2 (MI+) Always Below 1 Ω
D142-6 (MO-) - G111-3 (MI-) Always Below 1 Ω
D142-7 (SLDO) - G111-4 (SLDI) Always Below 1 Ω
D142-2 (MI+) or G111-5 (MO+) - Body ground Always 10 kΩ or higher
D142-3 (MI-) or G111-6 (MO-) - Body ground Always 10 kΩ or higher
D142-4 (SLDI) or G111-7 (SLDO) - Body ground Always 10 kΩ or higher
D142-5 (MO+) or G111-2 (MI+) - Body ground Always 10 kΩ or higher
D142-6 (MO-) or G111-3 (MI-) - Body ground Always 10 kΩ or higher
D142-7 (SLDO) or G111-4 (SLDI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

Pre-procedure1

a.

Replace the stereo component amplifier assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)

Pre-procedure1

a.

Disconnect the G111 stereo component amplifier assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G111)Location & Routing

Click Connector(G111)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assembly

G111-8 (WUI) - Body ground Ignition switch ACC 4.5 V or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR