Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Visual Mute Signal Circuit between Radio Receiver and Multi-display  


DESCRIPTION

The radio receiver assembly sends a visual mute signal to the multi-display assembly. As a result, a black screen is displayed when the screen changes so that noise and distorted images are not displayed.

When an open exists in the circuit, noise and distorted images will be displayed instead of a black screen.

When a short exists in the circuit, even though the multi-display assembly is operating normally, noise and distorted images will be displayed (black screen will not be displayed) during screen changes or the black screen will always be displayed.

WIRING DIAGRAM

E436385E03
1.188,1.031 1.802,1.229 0.615,0.198 10 false VMTF 1.667,0.917 2.281,1.115 0.615,0.198 10 false 1 5.208,0.906 5.823,1.104 0.615,0.198 10 false 11 5.458,1.021 5.958,1.26 0.5,0.24 10 false VMTI 0.51,1.938 1.125,2.135 0.615,0.198 10 false D64 0.51,2.104 2.208,2.406 1.698,0.302 10 false Radio Receiver Assembly 5.24,2.125 6.802,2.406 1.563,0.281 10 false Multi-display Assembly 5.24,1.938 5.854,2.135 0.615,0.198 10 false D60 2.635,2.125 5.521,2.604 2.885,0.479 10 false Integration Control Sub-assembly 3,1.031 3.615,1.229 0.615,0.198 10 false VMT1 3.604,1.031 4.219,1.229 0.615,0.198 10 false VMTR 2.646,1.958 3.26,2.156 0.615,0.198 10 false D105 2.74,0.917 3.354,1.115 0.615,0.198 10 false 39 4.115,0.917 4.729,1.115 0.615,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the integration control sub-assembly, always replace it with a new one. If a integration control sub-assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The integration control sub-assembly may not operate normally.




PROCEDURE

1.INSPECT INTEGRATION CONTROL SUB-ASSEMBLY
a.
E436386C04
1.5,0.385 1.917,0.646 0.417,0.26 0.583,1.302 0.865,1.698 true 1.552,0.427 2.01,0.625 0.458,0.198 10 false D105 0.75,1.729 1.365,1.927 0.615,0.198 10 false VMT1 0.188,0.156 0.479,0.354 0.292,0.198 10 false *a
*a Component without harness connected
(Integration Control Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D105)Location & Routing

Click Connector(D105)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D105-39 (VMT1) - Body ground Ignition switch ACC
Screen display changing
3.5 V or higher
→ Below 1 V
→ 3.5 V or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MULTI-DISPLAY ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
2.INSPECT MULTI-DISPLAY ASSEMBLY
a.
E429904C04
1.5,0.833 1.917,1.083 0.417,0.25 0.563,1.542 1.146,1.823 true 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.875 1.948,1.083 0.354,0.208 10 false D60 0.198,1.458 0.625,1.625 0.427,0.167 10 false VMTI
*a Component with harness connected
(Multi-display Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D60)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D60-11 (VMTI) - Body ground Ignition switch ACC
Screen display changing
3.5 V or higher
→ Below 1 V
→ 3.5 V or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the D105 integration control sub-assembly connector.


b.

Disconnect the D60 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D105,D60)Location & Routing

Click Connector(D105)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D105-17 (VMTR) - D60-11 (VMTI) Always Below 1 Ω
D105-17 (VMTR) or D60-11 (VMTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


b.

Check that the screen display is normal.

OK:

Screen display is normal.



Result:
Proceed to
OK
NG



OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the D105 integration control sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,D105)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D105)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D64-1 (VMTF) - D105-39 (VMT1) Always Below 1 Ω
D64-1 (VMTF) or D105-39 (VMT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY
a.

Replace the integration control sub-assembly with a new one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL


b.

Check that the screen display is normal.

OK:

Screen display is normal.



Result:
Proceed to
OK
NG



OK

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY