Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM L

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  PRECAUTION  


PRECAUTIONS FOR INSPECTING ELECTRONIC SHIFT LEVER SYSTEM


a.

The shift control ECU is a network management-compatible ECU. Therefore, the power source turns on when CAN communication is established.


b.

When the ignition switch is turned off, the shift control ECU will not shut down immediately. Therefore, when a fail-safe function is operating, if the ignition switch is operated repeatedly within a short period of time, the fail-safe function will not be canceled. After turning the ignition switch off, wait approximately 1 minute or more for the shift control ECU to completely shut down before connecting the GTS, opening/closing a door or operating a pedal.


c.

Do not change the shift state between park (P) and any other shift state repeatedly within a short period of time, otherwise the shift state will not be able to be changed from park (P) for a certain period of time to protect the system. If the system protection function operates, wait approximately 30 seconds before attempting to change the shift state.


d.

If the shift state cannot be changed from park (P), the auxiliary battery voltage may be low. Also, the shift state may automatically change to park (P) if the auxiliary battery voltage drops when the shift state not in park (P).


e.

If the electronic shift lever system has been damaged due to a flood, etc., the shift state will not be able to be changed to or from park (P).

When the shift state cannot be changed from park (P) to any other state, transport the vehicle by using the forced parking lock release mechanism to release the parking lock.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>FORCED RELEASE>OPERATION METHOD


f.

If the electronic shift lever system is damaged, the ignition switch may be turned to ACC when attempting to turn the ignition switch off. In this case, applying the electric parking brake may turn off the ignition switch.


g.

Do not turn the ignition switch off while the vehicle is being towed. The rear wheels may be secured by the parking lock according to the automatic park (P) function operating, leading to unforeseen accidents.


h.

If a fail-safe function is operating due to a malfunction or the auxiliary battery voltage becoming low, a warning message may be continuously displayed on the multi-information display until the shift state is changed from park (P) to any other state, even if the malfunction has been repaired or the auxiliary battery has been charged.


i.

The vehicle is equipped with a shift control supply. Therefore, if the auxiliary battery is removed with the ignition switch ON, power failure is determined and the shift state may automatically be changed to park (P).


j.

Before disconnecting the cable from the negative (-) auxiliary battery terminal, check that the electric parking brake is operating and the shift state is in park (P).



CAN COMMUNICATION SYSTEM PRECAUTIONS


a.

The CAN communication system is used for communication between the shift control ECU, the EV control ECU, the certification ECU (smart key ECU assembly) and other ECUs. If there are any problems in the CAN communication lines, corresponding DTCs are output.


b.

If any CAN communication DTCs are output, repair the malfunction and troubleshoot the electronic shift lever system after communication becomes normal.



PRECAUTION FOR REPLACING SHIFT CONTROL ECU


NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.


1.

Turn the ignition switch off.

2.

Check that the ODO meter display has turned off.

HINT:

After turning the ignition switch off, the ODO meter turns off after roughly 30 seconds and the shift control supply module assembly enters sleep mode.




CONFIRMATION WORK AFTER REPLACING SHIFT CONTROL ECU


a.

After replacing the shift control ECU, check for the following symptoms. If any of these symptoms exists, be sure to perform the following procedure starting from step b.

·

The P position switch blinks when the power switch is turned on (IG) or on (READY) and the shift position is not in P.

·

The power source off automatic P function does not operate.

·

The shift position is not displayed on the meter until a shift change operation is performed.



b.

Turn the power switch on (IG).


c.

Press the P position switch and change the shift position to P.


d.

Turn the power switch on (READY).


e.

Depress the brake pedal and operate the shift lever to change the shift position to D.


f.

Check that the P position switch does not blink when the power switch is turned on (IG) or on (READY), and the shift position is not in P.

NOTICE:

If the P position switch is blinking, be sure to perform steps b. through e. again.