Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM J

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  "Shift system malfunction Stop in a safe place See owner's manual" is Displayed on Multi-information Display  


CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (EV)
a.

Turn the ignition switch to ON.


b.

With the brake pedal depressed, while slowly move the shift lever as follows: N → R → N → D → Br.

HINT:

Wait with the shift lever in each position for 5 seconds or more.



c.

Push the P position switch (parking switch) to select park (P).


d.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
None of the DTCs are output. A
Any of the DTCs are output. B



e.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)

B

GO TO DTC CHART

2.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)
a.
for LHD:
C452170

for RHD:
C450295

Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))
a.
for LHD:
C452171

for RHD:
C450294

Check the connector connections and contact pressure of the relevant terminals for the shift lever position sensor (shift lock control unit assembly) connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))
a.

Disconnect the D93 shift control ECU connector.


b.

Disconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D16)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D16)Instrument Panel>Instrument Panel Wire>Shift Lock Control Unit Assembly

D93-20 (VCX1) - D16-4 (VCX1) Always Below 1 Ω
D93-22 (VCX2) - D16-12 (VCX2) Always Below 1 Ω
D93-19 (VSI1) - D16-7 (VSX1) Always Below 1 Ω
D93-21 (VSI2) - D16-5 (VSX2) Always Below 1 Ω
D93-23 (VSI3) - D16-11 (VSX3) Always Below 1 Ω
D93-25 (VSI4) - D16-9 (VSX4) Always Below 1 Ω
D93-24 (E2X1) - D16-14 (E2X1) Always Below 1 Ω
D93-26 (E2X2) - D16-2 (E2X2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D16)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D16)Instrument Panel>Instrument Panel Wire>Shift Lock Control Unit Assembly

D93-20 (VCX1) or D16-4 (VCX1) - Body ground and other terminals Always 10 kΩ or higher
D93-22 (VCX2) or D16-12 (VCX2) - Body ground and other terminals Always 10 kΩ or higher
D93-19 (VSI1) or D16-7 (VSX1) - Body ground and other terminals Always 10 kΩ or higher
D93-21 (VSI2) or D16-5 (VSX2) - Body ground and other terminals Always 10 kΩ or higher
D93-23 (VSI3) or D16-11 (VSX3) - Body ground and other terminals Always 10 kΩ or higher
D93-25 (VSI4) or D16-9 (VSX4) - Body ground and other terminals Always 10 kΩ or higher
D93-24 (E2X1) or D16-14 (E2X1) - Body ground and other terminals Always 10 kΩ or higher
D93-26 (E2X2) or D16-2 (E2X2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


e.

Reconnect the D93 shift control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR