Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2020.11–2021.08
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2177  Initialization not Completed  


DESCRIPTION

Initialization is necessary if one of the following occurs:

·

The tire pressure warning ECU and receiver is replaced.

·

A tire pressure warning valve and transmitter is replaced.

·

Tires with different standard tire pressures are installed.

·

A new vehicle is delivered.


Tire pressure warning initialization is performed when the steering pad switch assembly is operated with the ignition switch ON, "Initialization" is selected on the multi-information display and the "OK" switch (steering pad switch assembly) is pressed and held.

When an initialization request signal is received, the tire pressure warning ECU and receiver blinks the tire pressure warning light in the combination meter assembly 3 times and registers the tire pressure information sent from the tire pressure warning valve and transmitters.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C2177 Initialization not Completed All conditions below are met:
·

During initialization

·

Tire pressure warning valve and transmitter is not in stop mode

·

Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more

·

Vehicle speed is more than 40 km/h (25 mph) for 20 minutes or more


·

Tire pressure warning valve and transmitter

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


Tire Pressure Monitor A

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

·

Initialization will not complete and DTC C2177 may be stored in the tire pressure warning ECU and receiver if the GTS is used to perform initialization with the ECU Data Item list displayed for 10 minutes or longer.



PROCEDURE

1.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings, or devices installed by the user.




Result:
Proceed to
OK
NG



OK

2.PERFORM INITIALIZATION

NG

CHECK IF ANY DEVICE IS INSTALLED BY USER

2.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
50003 203 36,37,38,39
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID 3 Tire Inflation Pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID 4 Tire Inflation Pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




Result:
Result Proceed to
All tire pressure readings are equal to specified values. A
Tire pressure values are not displayed. B



A

END

B