Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2020.11–2021.08
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2121  No Signal from Transmitter ID1  C2122  No Signal from Transmitter ID2  C2123  No Signal from Transmitter ID3  C2124  No Signal from Transmitter ID4  C2181  Transmitter ID1 not Received (Test Mode DTC)  C2182  Transmitter ID2 not Received (Test Mode DTC)  C2183  Transmitter ID3 not Received (Test Mode DTC)  C2184  Transmitter ID4 not Received (Test Mode DTC)  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.

Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.

·

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

·

Devices using similar radio frequencies are used in the vehicle.

·

The ID of a tire pressure warning valve and transmitter is mistyped during registration.

·

A tire, wheel and/or transmitter from a different vehicle is installed.


HINT:

When no transmitter ID is received from a tire pressure warning valve and transmitter for 20 minutes*1 (10 minutes*2) or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2 or more, DTCs from C2121 to C2124 are stored.

DTCs C2121 to C2124 can only be cleared by using the GTS. DTCs C2181 to C2184 can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181 to C2184 are output only in test mode.

*1: for FMVSS138 Type

*2: for ECE-R64 Type



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C2121 No Signal from Transmitter ID1 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2122 No Signal from Transmitter ID2 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2123 No Signal from Transmitter ID3 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2124 No Signal from Transmitter ID4 Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

Any transmitter ID is not received from tire pressure warning valve and transmitters.

·

Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more.


(b) When both conditions below are met:
·

Tire pressure warning valve and transmitter is not in stop mode.

·

No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more.


·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2181 Transmitter ID1 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2182 Transmitter ID2 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2183 Transmitter ID3 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A
C2184 Transmitter ID4 not Received (Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A

*1: for FMVSS138 Type

*2: for ECE-R64 Type


DTC Detection Conditions: C2121
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3

*1: for FMVSS138 Type

*2: for ECE-R64 Type

Diagnosis Condition Tire pressure warning valve and transmitter is not in stop mode. ○ ○ ○
Vehicle speed is more than 40 km/h (25 mph). ○ - -
No vehicle speed signal is received. - ○ -
Malfunction Status Any transmitter ID is not received from tire pressure warning valve and transmitters. ○ ○ -
No transmitter ID is received from tire pressure warning valve and transmitters. - - ○
Detection Time 20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
Number of Trips - - -

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C2122
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3

*1: for FMVSS138 Type

*2: for ECE-R64 Type

Diagnosis Condition Tire pressure warning valve and transmitter is not in stop mode. ○ ○ ○
Vehicle speed is more than 40 km/h (25 mph). ○ - -
No vehicle speed signal is received. - ○ -
Malfunction Status Any transmitter ID is not received from tire pressure warning valve and transmitters. ○ ○ -
No transmitter ID is received from tire pressure warning valve and transmitters. - - ○
Detection Time 20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
Number of Trips - - -

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C2123
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3

*1: for FMVSS138 Type

*2: for ECE-R64 Type

Diagnosis Condition Tire pressure warning valve and transmitter is not in stop mode. ○ ○ ○
Vehicle speed is more than 40 km/h (25 mph). ○ - -
No vehicle speed signal is received. - ○ -
Malfunction Status Any transmitter ID is not received from tire pressure warning valve and transmitters. ○ ○ -
No transmitter ID is received from tire pressure warning valve and transmitters. - - ○
Detection Time 20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
Number of Trips - - -

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C2124
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3

*1: for FMVSS138 Type

*2: for ECE-R64 Type

Diagnosis Condition Tire pressure warning valve and transmitter is not in stop mode. ○ ○ ○
Vehicle speed is more than 40 km/h (25 mph). ○ - -
No vehicle speed signal is received. - ○ -
Malfunction Status Any transmitter ID is not received from tire pressure warning valve and transmitters. ○ ○ -
No transmitter ID is received from tire pressure warning valve and transmitters. - - ○
Detection Time 20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
20 minutes or more (*1)
10 minutes or more (*2)
Number of Trips - - -

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


NOTICE:
·

When DTCs C2121 to C2124 are stored, DTC C2179 may be stored simultaneously. In such cases, troubleshoot DTCs C2121 to C2124 first, then troubleshoot DTC C2179.

·

If the GTS is used to display the ECU Data List for 10 minutes or more, DTCs C2121, C2122, C2123 and C2124 are stored to the tire pressure warning ECU.

If these DTCs are stored, clear the DTCs using the GTS.

·

If any of the DTCs from C2121 to C2124 is output, clear the DTCs or drive at 40 km/h (25 mph) for 1 minute or more.



HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
excluding JPD20R-CEDSSW (w/ Panic Switch) A
for JPD20R-CEDSSW (w/ Panic Switch) B



A

2.CHECK FREQUENCY RECEIVING CONDITION

B

13.CHECK FREQUENCY RECEIVING CONDITION
2.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.




Result:
Result Proceed to
There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. A
There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. B



A

3.CHECK WIRELESS DOOR LOCK FUNCTION

B

9.CLEAR DTC
3.CHECK WIRELESS DOOR LOCK FUNCTION
a.

Check the wireless door lock function using the electrical key transmitter sub-assembly switch.


Result:
Result Proceed to
Operates normally A
Does not operate normally B



A

4.CONFIRM OUTPUT DTC

B

4.CONFIRM OUTPUT DTC
a.

Check the stored DTC.


Result:
Result Proceed to
Any DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) A
All DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) B



A

5.IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

B

7.TEST MODE INSPECTION (C2181, C2182, C2183, C2184)
5.IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

Pre-procedure1

a.

Display the "ID Tire Position" value for each wheel using the GTS.


Procedure1

a.

Refer to the following chart and check the wheel position of the DTC and transmitter match.

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Position
ID 2 Tire Position
ID 3 Tire Position
ID 4 Tire Position
50003 203 78,54,55,56
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Position ID1 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID1 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 2 Tire Position ID2 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID2 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 3 Tire Position ID3 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID3 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
ID 4 Tire Position ID4 Tire Position No Information or FL or FR or RL or RR or Spare or Judging ID4 tire position is displayed If no tire position information is stored, "No Information" will be displayed.
HINT:

Refer to the following chart for the Data List items that correspond to the DTCs.

DTC No. Detection Item Data List
C2121 No Signal from Transmitter ID1 ID1 Tire Position
C2181 Transmitter ID 1 not Received (for Test Diagnosis)
C2122 No Signal from Transmitter ID2 ID2 Tire Position
C2182 Transmitter ID 2 not Received (for Test Diagnosis)
C2123 No Signal from Transmitter ID3 ID3 Tire Position
C2183 Transmitter ID 3 not Received (for Test Diagnosis)
C2124 No Signal from Transmitter ID4 ID4 Tire Position
C2184 Transmitter ID 4 not Received (for Test Diagnosis)



Result:
Proceed to
NEXT


Post-procedure1

a.

None



NEXT

6.CHECK TRANSMITTER ID
6.CHECK TRANSMITTER ID

Pre-procedure1

a.

Refer to the following chart and record the tire pressure warning valve and transmitter ID of the output DTC.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.

·

Refer to the following chart for the Data List items that correspond to the DTCs.

DTC No. Detection Item Data List
C2121 No Signal from Transmitter ID1 Registered ID 1 code
C2181 Transmitter ID 1 not Received (for Test Diagnosis)
C2122 No Signal from Transmitter ID2 Registered ID 2 code
C2182 Transmitter ID 2 not Received (for Test Diagnosis)
C2123 No Signal from Transmitter ID3 Registered ID 3 code
C2183 Transmitter ID 3 not Received (for Test Diagnosis)
C2124 No Signal from Transmitter ID4 Registered ID 4 code
C2184 Transmitter ID 4 not Received (for Test Diagnosis)




b.

Disassemble the tire indicated in the output DTC and check the tire pressure warning valve and transmitter ID.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

a.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

a.

None



A

REPLACE CORRESPONDING TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

10.REGISTRATION OF TRANSMITTER ID
7.TEST MODE INSPECTION (C2181, C2182, C2183, C2184)
a.

Perform a test mode inspection and perform a send data check (C2181, C2182, C2183, C2184).

HINT:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

END

Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.


NG

8.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER
8.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER

Pre-procedure1

a.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




b.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

a.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

a.

None



A

B

10.REGISTRATION OF TRANSMITTER ID
9.CLEAR DTC
a.

Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

Result:
Proceed to
NEXT



NEXT

END

Explain to the customer that there is a high possibility that a device (located near or inside the vehicle) or facility using electrical waves of approximately the same frequency is causing electrical wave interference.


10.REGISTRATION OF TRANSMITTER ID
a.

Perform ID registration for the tire pressure warning valve and receiver.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

11.PERFORM INITIALIZATION
11.PERFORM INITIALIZATION

Pre-procedure1

a.

Set the tire pressure to the specified value.

HINT:

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION



Procedure1

a.

Initialize the tire pressure warning system.

HINT:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT


Post-procedure1

a.

None



NEXT

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

Result:
Proceed to
NEXT



NEXT

END

13.CHECK FREQUENCY RECEIVING CONDITION
a.

Check that the following conditions are not met:

i.

Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

HINT:

If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.



ii.

Devices using similar radio frequencies are used in the vehicle.

OK:

Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.


HINT:

Radio transmissions may be interrupted due to the surroundings or devices installed by the user.




Result:
Result Proceed to
There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. A
There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. B



A

14.CONFIRM OUTPUT DTC

B

9.CLEAR DTC
14.CONFIRM OUTPUT DTC
a.

Check the stored DTC.


Result:
Result Proceed to
Any DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) A
All DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) B



A

5.IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION)

B

15.TEST MODE INSPECTION (C2181, C2182, C2183, C2184)
15.TEST MODE INSPECTION (C2181, C2182, C2183, C2184)
a.

Perform a test mode inspection and perform a send data check (C2181, C2182, C2183, C2184).

HINT:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

END

Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.


NG

16.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER
16.CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER

Pre-procedure1

a.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




b.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

a.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

a.

None



A

B

10.REGISTRATION OF TRANSMITTER ID