Home › Vehicle Interior › MIRROR (INT) › DIGITAL REAR-VIEW MIRROR SYSTEM
RM37H0E _58 Vehicle Interior _095286 MIRROR (INT) _0454993 DIGITAL REAR-VIEW MIRROR SYSTEM J

MIRROR (INT)  DIGITAL REAR-VIEW MIRROR SYSTEM  The Camera Indicator is not Displayed  


DESCRIPTION

Power is supplied to the inner rear view mirror assembly through the following circuit.

WIRING DIAGRAM

B601019E03
0.427,2.073 1.333,2.51 0.906,0.438 10 false from Auxiliary Battery 0.427,0.698 1.25,1.135 0.823,0.438 10 false from IG1 D NO.1 Relay 1.76,2.271 3,2.5 1.24,0.229 10 false MPX-B D NO.1*1 1.844,0.854 3.083,1.083 1.24,0.229 10 false IG1 D NO.2*1 3.271,3.01 5.104,3.365 1.833,0.354 10 false Map Light Assembly 4.948,4.24 7.104,4.635 2.156,0.396 10 false Inner Rear View Mirror Assembly 4.958,4.073 7.115,4.469 2.156,0.396 10 false H14 3.281,2.813 3.656,3.094 0.375,0.281 10 false H8 3.542,0.583 3.917,0.865 0.375,0.281 10 false IG 3.51,2 3.885,2.281 0.375,0.281 10 false +B2 4.063,2 4.438,2.281 0.375,0.281 10 false +B3 4.083,0.583 4.458,0.865 0.375,0.281 10 false IG1 5.458,2.104 7.156,2.417 1.698,0.313 10 false +B 5.458,0.688 7.156,1 1.698,0.313 10 false IG 5.458,3.521 7.156,3.833 1.698,0.313 10 false E 5.219,2 7.156,2.229 1.938,0.229 10 false 6 5.219,0.583 7.156,0.813 1.938,0.229 10 false 1 5.219,3.417 7.156,3.646 1.938,0.229 10 false 2 3.323,0.583 3.698,0.865 0.375,0.281 10 false 1 3.25,2 3.625,2.281 0.375,0.281 10 false 2 4.385,2.01 4.76,2.292 0.375,0.281 10 false 3 4.375,0.583 4.75,0.865 0.375,0.281 10 false 15 1.844,1.073 3.083,1.302 1.24,0.229 10 false IG1 P NO.2*2 1.76,2.49 3,2.719 1.24,0.229 10 false MPX-B P NO.1*2 1.292,3.885 2.531,4.115 1.24,0.229 10 false *1: for LHD 1.271,4.292 2.51,4.521 1.24,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - POWER SUPPLY)
a.

Disconnect the H14 inner rear view mirror assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H14)Location & Routing

Click Connector(H14)Body>No. 1 Roof Wire>Inner Rear View Mirror Assembly

H14-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H14-6 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - POWER SUPPLY)
2.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - BODY GROUND)
a.

Disconnect the H14 inner rear view mirror assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H14)Location & Routing

Click Connector(H14)Body>No. 1 Roof Wire>Inner Rear View Mirror Assembly

H14-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - POWER SUPPLY)
a.

Disconnect the H8 map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H8-2 (+B2) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INNER REAR VIEW MIRROR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INNER REAR VIEW MIRROR ASSEMBLY)
a.

Disconnect the H14 inner rear view mirror assembly connector.


b.

Disconnect the H8 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H14,H8)Location & Routing

Click Connector(H14)Body>No. 1 Roof Wire>Inner Rear View Mirror Assembly

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H14-1 (IG) - H8-15 (IG1) Always Below 1 Ω
H14-6 (+B) - H8-3 (+B3) Always Below 1 Ω
H14-1 (IG) or H8-15 (IG1) - Body ground Always 10 kΩ or higher
H14-6 (+B) or H8-3 (+B3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR