Home › Vehicle Interior › METER / GAUGE / DISPLAY › HEADUP DISPLAY SYSTEM
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0455144 HEADUP DISPLAY SYSTEM C

METER / GAUGE / DISPLAY  HEADUP DISPLAY SYSTEM  B132187  Lost Communication with EMV Missing Message  


DESCRIPTION

The meter mirror sub-assembly receives signals from the radio receiver assembly via local bus communication and displays audio system and navigation system information on the headup display.

This DTC is stored when the meter mirror sub-assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B132187 Lost Communication with EMV Missing Message
·

DTC Detection Condition: IG+ voltage 9.5 to 11.5 V or higher


·

Malfunction Status: Lost communication with radio receiver assembly


·

Malfunction Duration: 10 seconds or more


·

Harness or connector

·

Meter mirror sub-assembly

·

Radio receiver assembly


DTC stored Head Up Display A

Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Meter Mirror Sub-assembly (Head Up Display) Radio Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187 Local bus (Open or short)
Meter mirror sub-assembly (Internal malfunction)
Combination meter assembly (Internal malfunction)
Radio receiver assembly (Internal malfunction)
Pattern 2 B132187 - B1325 - Combination meter assembly (Internal malfunction)
Pattern 3 B132187 - - B132187 Radio receiver assembly (Internal malfunction)
Pattern 4 B132187 - - - Meter mirror sub-assembly (Internal malfunction)

WIRING DIAGRAM

C432290E17
1.302,1.771 1.917,1.969 0.615,0.198 10 false D64 1.292,1.948 3.01,2.521 1.719,0.573 10 false Radio Receiver Assembly 1.74,1.26 2.354,1.458 0.615,0.198 10 false CNL1 4.979,1.781 5.594,1.979 0.615,0.198 10 false D95 4.833,1.115 5.448,1.313 0.615,0.198 10 false 15 2.24,1.115 2.854,1.313 0.615,0.198 10 false 6 1.719,0.708 2.333,0.906 0.615,0.198 10 false CNH1 2.229,0.573 2.844,0.771 0.615,0.198 10 false 5 4.844,0.563 5.458,0.76 0.615,0.198 10 false 14 5.156,0.688 5.771,0.885 0.615,0.198 10 false TX+ 5.146,1.24 5.76,1.438 0.615,0.198 10 false TX- 4.969,1.958 6.167,2.333 1.198,0.375 10 false Meter Mirror Sub-assembly 1.125,4.104 1.74,4.302 0.615,0.198 10 false D41 1.115,4.281 2.99,4.479 1.875,0.198 10 false Combination Meter Assembly 1.823,3.031 2.438,3.229 0.615,0.198 10 false TX+ 2.208,2.885 2.823,3.083 0.615,0.198 10 false 8 1.844,3.583 2.458,3.781 0.615,0.198 10 false TX- 2.188,3.448 2.802,3.646 0.615,0.198 10 false 7 4.708,4.333 6.885,4.656 2.177,0.323 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

To measure the resistance of the CAN bus, turn the ignition switch off, wait at least 1 minutes without operating any keys or switches or opening or closing the doors, disconnect the auxiliary battery, wait at least 1 minutes again, and then measure the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Communication malfunction DTCs may be output if a radio receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with a new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:
·

When checking each connector, press the connector case in the direction of the connection before disconnecting the connectors, and check that there are no disconnections or looseness.

·

When disconnecting the connectors, check that there is no damage, deformation, or corrosion of the connector terminals and connector case.

·

Depending on the parts that are replaced, performing initialization, registration or calibration may be needed.



PROCEDURE

1.CHECK FOR DTC
a.

Check each system for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Body Electrical > Combination Meter > Trouble Codes
50001 409
Body Electrical > Head Up Display > Trouble Codes
50001 408

Pattern DTC Output Part Name
(Display on GTS)
Meter Mirror Sub-assembly (Head Up Display) Radio Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187
Pattern 2 B132187 - -
Pattern 3 B132187 - - B132187
Pattern 4 B132187 - - -

Result:
Result Proceed to
Pattern 1 is output A
Pattern 2 is output B
Pattern 3 is output C
Pattern 4 is output D



A

GO TO METER / GAUGE SYSTEM (B132187)

B

2.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

C

REPLACE RADIO RECEIVER ASSEMBLY

D

REPLACE METER MIRROR SUB-ASSEMBLY

2.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the meter mirror sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-14 (TX+) - D95-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN WIRE OR CONNECTOR