Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2020.11–2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0455415 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


B345456N25
3.323,0.104 3.823,0.354 0.5,0.25 3.438,0.156 3.917,0.406 0.479,0.25 10 false D41

a.

Disconnect the D41 combination meter assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/o All Auto Control

D41-22 (B) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
D41-21 (IG+) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
D41-31 (ES) - Body ground Ground Always Below 1 Ω
D41-14 (RLSB) - Body ground Rear occupant detection sensor LH signal signal Rear LH seat occupaied 10 kΩ or higher
Rear LH seat not occupaied Below 1 Ω
D41-12 (RRSB) - Body ground Rear occupant detection sensor RH signal Rear RH seat occupaied 10 kΩ or higher
Rear RH seat not occupaied Below 1 Ω
D41-13 (RCSB) - Body ground Rear occupant detection sensor center signal signal Rear center seat occupaied 10 kΩ or higher
Rear center seat not occupaied Below 1 Ω
D41-6 (PODS) - Body ground Occupant detection sensor signal Front passenger seat occupaied Below 100 Ω
Front passenger seat not occupaied 1 MΩ or higher
D41-18 (PBKL) - Body ground* Front passenger seat belt buckle switch signal Front passenger seat belt fastened 10 kΩ or higher
Front passenger seat belt unfastened Below 1 Ω



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C01
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-32 (IG) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-18 (DBKL) - Body ground Driver seat belt buckle switch signal Driver seat belt fastened 10 kΩ or higher
Driver seat belt unfastened Below 1 Ω



EV CONTROL ECU


A352214C13
0.646,0.271 1.115,0.625 0.469,0.354 1.958,0.271 2.427,0.625 0.469,0.354 3.365,0.271 3.833,0.625 0.469,0.354 4.729,0.271 5.198,0.625 0.469,0.354 6.021,0.271 6.49,0.625 0.469,0.354 0.156,0.188 0.469,0.385 0.313,0.198 10 false *1 0.76,0.375 1.219,0.573 0.458,0.198 10 false G14 2.083,0.375 2.542,0.573 0.458,0.198 10 false A15 3.49,0.385 3.948,0.583 0.458,0.198 10 false A16 4.833,0.385 5.292,0.583 0.458,0.198 10 false A17 6.188,0.385 6.646,0.583 0.458,0.198 10 false A8
*1 EV Control ECU - -


a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ All Auto Control

A8-1(BATT) - A17-4(E1) Constant power source Ignition switch ON 11 to 14 V
Ignition switch ON (READY) 11 to 15.5 V
A16-7(IG2) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A17-1(+B1) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A8-7(+B2) - A17-4(E1) Power source Ignition switch ON 11 to 14 V
A16-8 (BRFC) - Body ground* Rear RH seat belt buckle switch signal Rear RH seat belt fastened 10 kΩ or higher
Rear RH seat belt unfastened Below 1 Ω
A16-18 (BLFC) - Body ground* Rear LH seat belt buckle switch signal Rear LH seat belt fastened 10 kΩ or higher
Rear LH seat belt unfastened Below 1 Ω
A16-28 (BCFC) - Body ground* Rear center seat belt buckle switch signal Rear center seat belt fastened 10 kΩ or higher
Rear center seat belt unfastened Below 1 Ω