Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2020.11–2021.08
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455112 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 7 CAN junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (A)

·

Power source circuit of blind spot monitor sensor LH (A)

·

Blind spot monitor sensor LH (A) ground circuit

·

Blind spot monitor sensor RH (B)


Clearance Warning A
U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 7 CAN junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (B)

·

Power source circuit of blind spot monitor sensor RH (B)

·

Blind spot monitor sensor RH (B) ground circuit

·

Blind spot monitor sensor LH (A)


Clearance Warning A

WIRING DIAGRAM

E386359E26
4.271,4.479 5.583,4.844 1.313,0.365 10 false No. 7 CAN Junction Connector 4.271,4.292 4.75,4.521 0.479,0.229 10 false G130 4.125,3.438 4.302,3.635 0.177,0.198 10 false 1 4.063,3.802 4.271,3.979 0.208,0.177 10 false 12 3.792,3.438 4.052,3.677 0.26,0.24 10 false 37 3.792,3.802 4.052,4.042 0.26,0.24 10 false 38 3.302,3.542 3.719,3.74 0.417,0.198 10 false CANH 3.302,3.906 3.781,4.104 0.479,0.198 10 false CANL 2.646,4.406 3.875,4.969 1.229,0.563 10 false Clearance Warning ECU Assembly 2.656,4.24 3.104,4.427 0.448,0.188 10 false G20 4.094,0.813 4.24,1 0.146,0.188 10 false 2 4.063,1.448 4.281,1.635 0.219,0.188 10 false 13 5.521,0.813 5.688,0.979 0.167,0.167 10 false 1 5.521,1.438 5.688,1.604 0.167,0.167 10 false 6 3.26,0.833 3.875,1.031 0.615,0.198 10 false CA2P 5.75,0.833 6.156,1.042 0.406,0.208 10 false CA2P 5.75,1.708 6.365,1.906 0.615,0.198 10 false CA2N 3.229,1.729 3.844,1.927 0.615,0.198 10 false CA2N 3.719,0.823 3.99,1.042 0.271,0.219 10 false 1 3.74,1.448 4.01,1.667 0.271,0.219 10 false 6 2.49,1.021 2.76,1.24 0.271,0.219 10 false 5 2.417,1.708 2.688,1.927 0.271,0.219 10 false 10 2.667,1.115 2.969,1.302 0.302,0.188 10 false BLB 2.677,1.802 3.125,2 0.448,0.198 10 false BLGD 6.25,1.833 6.708,2.031 0.458,0.198 10 false BRGD 6.354,1.115 6.729,1.302 0.375,0.188 10 false BRB 6.76,1 6.927,1.188 0.167,0.188 10 false 5 6.74,1.729 7.01,1.948 0.271,0.219 10 false 10 2.573,2.5 3.74,2.896 1.167,0.396 10 false Blind Spot Monitor Sensor LH (A) 2.594,2.323 2.885,2.51 0.292,0.188 10 false G60 5.688,2.323 6,2.521 0.313,0.198 10 false G56 5.115,1.438 5.323,1.625 0.208,0.188 10 false 14 5.135,0.813 5.313,1 0.177,0.188 10 false 3 1.333,0.531 2.26,0.719 0.927,0.188 10 false LUG-IG1 NO.2 0.25,0.292 1.115,0.688 0.865,0.396 10 false from LUG-IG1 NO.1 Relay 5.688,2.49 6.844,2.875 1.156,0.385 10 false Blind Spot Monitor Sensor RH (B)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTCs are not output A
Only U117787 is output B
Only U117887 is output C
U117787 and U117887 are output D



A

B

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - BATTERY AND BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - BATTERY AND BODY GROUND)

D

9.CHECK CAN BUS MAIN WIRE
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the blind spot monitor sensor LH (A) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-10 (BLGD) - Body ground Always Below 1 Ω



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
G60-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH [A])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH [A])

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor LH (A) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-1 (CA2P) - G60-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the blind spot monitor sensor LH (A) connector.


b.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-2 (CANH) - G130-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH [A] - NO. 7 CAN JUNCTION CONNECTOR)

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the blind spot monitor sensor RH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-10 (BRGD) - Body ground Always Below 1 Ω



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
G56-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH [B])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH [B])

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH (B) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-1 (CA2P) - G56-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 CAN JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the blind spot monitor sensor RH (B) connector.


b.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-3 (CANH) - G130-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH [B] - NO. 7 CAN JUNCTION CONNECTOR)

9.CHECK CAN BUS MAIN WIRE

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20,D20)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G20-37 (CANH) - G20-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G20-37 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-38 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-37 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G20-38 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
G20-37 (CANH) - G20-38 (CANL) is more than or equal to 70 Ω A
G20-37 (CANH) - G20-38 (CANL) is less than or equal to 54 Ω B
G20-37 (CANH) - D20-4 (CG) is less than or equal to 200 Ω C
G20-38 (CANL) - D20-4 (CG) is less than or equal to 200 Ω D
G20-37 (CANH) - D20-16 (BAT) is less than or equal to 6 kΩ E
G20-38 (CANL) - D20-16 (BAT) is less than or equal to 6 kΩ F
None of the above conditions are met G


Post-procedure1

a.

None



A

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

B

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

C

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

D

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

E

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

F

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

G

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-2 (CANH) - G130-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

NG

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (A))
11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-3 (CANH) - G130-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

NG

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (B))
12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the No. 7 CAN junction connector.

C443781C05
4.406,1.438 4.844,1.708 0.438,0.271 4.115,1.458 4.469,0.531 4.469,0.531 4.729,0.531 true 4.104,1.646 4.406,2.521 4.406,2.521 4.667,2.521 true 4.781,0.438 5.49,0.635 0.708,0.198 10 false CANH*b 4.719,2.417 5.25,2.594 0.531,0.177 10 false CANL*b 4.469,1.479 4.833,1.688 0.365,0.208 10 false G130 0.083,0.167 0.792,0.365 0.708,0.198 10 false *a
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-1 (CANH) - G130-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

NG

REPLACE NO. 7 CAN JUNCTION CONNECTOR

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (A))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (A) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-1 (CA2P) - G60-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 7 CAN JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (B))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (B) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-1 (CA2P) - G56-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 7 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-2 (CANH) - G130-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

NG

18.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-3 (CANH) - G130-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

NG

19.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))
17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

G130-1 (CANH) - G130-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

20.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (A) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G60-1 (CA2P) - G60-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 7 CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (B) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G56)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

G56-1 (CA2P) - G56-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 7 CAN JUNCTION CONNECTOR)

20.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

G20-37 (CANH) - G20-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130,D20)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G130-2 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-13 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-2 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G130-13 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

NG

24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130,D20)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G130-3 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-14 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-3 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G130-14 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

NG

25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))
23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the No. 7 CAN junction connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G130,D20)Location & Routing

Click Connector(G130)Body>Floor Wire / No. 3 Floor Wire>No. 7 CAN Junction Connector

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G130-1 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-12 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G130-1 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G130-12 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

26.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
24.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor LH (A) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G60,D20)Location & Routing

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G60-1 (CA2P) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G60-6 (CA2N) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G60-1 (CA2P) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G60-6 (CA2N) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 7 CAN JUNCTION CONNECTOR)

25.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the blind spot monitor sensor RH (B) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G56,D20)Location & Routing

Click Connector(G56)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor RH

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G56-1 (CA2P) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G56-6 (CA2N) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G56-1 (CA2P) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G56-6 (CA2N) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 7 CAN JUNCTION CONNECTOR)

26.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the G130 No. 7 CAN junction connector.


b.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G20,D20)Location & Routing

Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assembly

Click Connector(D20)Instrument Panel>Instrument Panel Wire>DLC3

G20-37 (CANH) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-38 (CANL) - D20-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-37 (CANH) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G20-38 (CANL) - D20-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)