Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455113 PARKING ASSIST MONITOR SYSTEM J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  Image from Camera for Parking Assist Monitor is Abnormal  


DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the display.

WIRING DIAGRAM

w/ Audio and Visual System:
E404564E14
5.708,0.552 6.167,0.75 0.458,0.198 10 false CA+ 5.771,1.063 6.229,1.26 0.458,0.198 10 false V+ 5.76,1.521 6.219,1.719 0.458,0.198 10 false V- 5.729,1.917 6.188,2.115 0.458,0.198 10 false CGND 5.438,0.531 5.896,0.729 0.458,0.198 10 false 30 5.469,1.01 5.927,1.208 0.458,0.198 10 false 28 5.479,1.5 5.938,1.698 0.458,0.198 10 false 29 5.49,1.958 5.948,2.156 0.458,0.198 10 false 27 3.333,2.417 4,2.615 0.667,0.198 10 false * 1.531,0.583 1.99,0.781 0.458,0.198 10 false 6 1.563,1.042 2.021,1.24 0.458,0.198 10 false 3 1.573,1.51 2.031,1.708 0.458,0.198 10 false 2 1.573,1.969 2.031,2.167 0.458,0.198 10 false 5 1.125,0.688 1.583,0.885 0.458,0.198 10 false CB+ 1.135,1.094 1.594,1.292 0.458,0.198 10 false CV+ 1.188,1.594 1.646,1.792 0.458,0.198 10 false CV- 1.031,2.031 1.49,2.229 0.458,0.198 10 false CGND 5.24,2.708 5.698,2.906 0.458,0.198 10 false D56 5.229,2.927 6.917,3.292 1.688,0.365 10 false Radio and Display Receiver Assembly 0.271,2.688 0.729,2.885 0.458,0.198 10 false K4 0.271,2.865 2.573,3.354 2.302,0.49 10 false Rear Television Camera Assembly 5.719,2.417 6.177,2.615 0.458,0.198 10 false CSLD 5.479,2.292 5.938,2.49 0.458,0.198 10 false 26 0.625,3.375 1.396,3.563 0.771,0.188 10 false *: Shielded

w/ Navigation System:
E382471E12
0.854,0.396 1.229,0.615 0.375,0.219 10 false CA+ 0.938,0.74 1.313,0.958 0.375,0.219 10 false V+ 0.969,1.042 1.344,1.26 0.375,0.219 10 false V- 0.76,1.385 1.292,1.615 0.531,0.229 10 false CGND 0.792,1.698 1.292,1.917 0.5,0.219 10 false CSLD 0.125,1.917 0.448,2.104 0.323,0.188 10 false D60 0.125,2.073 1.615,2.281 1.49,0.208 10 false Multi-display Assembly 0.146,2.417 1.073,2.625 0.927,0.208 10 false *: Shielded 1.292,0.281 1.667,0.5 0.375,0.219 10 false 10 1.354,0.615 1.729,0.833 0.375,0.219 10 false 8 1.354,0.948 1.729,1.167 0.375,0.219 10 false 9 1.302,1.271 1.677,1.49 0.375,0.219 10 false 21 1.292,1.563 1.667,1.781 0.375,0.219 10 false 20 3.635,1.688 3.844,1.885 0.208,0.198 10 false * 5.76,0.281 6.135,0.5 0.375,0.219 10 false 6 5.76,0.615 6.135,0.833 0.375,0.219 10 false 3 5.76,0.948 6.135,1.167 0.375,0.219 10 false 2 5.76,1.281 6.135,1.5 0.375,0.219 10 false 5 5.99,0.406 6.365,0.625 0.375,0.219 10 false CB+ 6,0.74 6.375,0.958 0.375,0.219 10 false CV+ 5.99,1.052 6.365,1.271 0.375,0.219 10 false CV- 5.99,1.417 6.552,1.604 0.563,0.188 10 false CGND 5.5,1.865 5.875,2.083 0.375,0.219 10 false K4 5.5,2.052 6.979,2.427 1.479,0.375 10 false Rear Television Camera Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When the "!" mark is displayed on the display after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



HINT:

Images may be unclear even in normal conditions if:

·

Electrical devices are used in the cabin (noise may occur in the image).

·

Accessories that generate radio waves have been installed (noise may occur in the image).

·

The display of radio and display receiver assembly is cold (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Audio and Visual System A
w/ Navigation System B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Disconnect the K4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56,K4)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

D56-30 (CA+) - K4-6 (CB+) Always Below 1 Ω
D56-28 (V+) - K4-3 (CV+) Always Below 1 Ω
D56-27 (CGND) - K4-5 (CGND) Always Below 1 Ω
D56-29 (V-) - K4-2 (CV-) Always Below 1 Ω
D56-30 (CA+) or K4-6 (CB+) - Body ground Always 10 kΩ or higher
D56-28 (V+) or K4-3 (CV+) - Body ground Always 10 kΩ or higher
D56-27 (CGND) or K4-5 (CGND) - Body ground Always 10 kΩ or higher
D56-29 (V-) or K4-2 (CV-) - Body ground Always 10 kΩ or higher
D56-26 (CSLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL

E404546C20
5.552,1.146 6.177,1.396 0.625,0.25 3.156,0.427 3.427,0.427 3.427,0.427 3.792,1.625 true 3.333,2.438 3.604,2.438 3.604,2.438 3.906,1.625 true 4.198,1.625 4.469,0.344 4.469,0.344 4.708,0.344 true 5.677,1.208 6.135,1.406 0.458,0.198 10 false D56 4.802,0.281 5.396,0.49 0.594,0.208 10 false CGND 3.135,2.354 3.729,2.563 0.594,0.208 10 false V- 2.875,0.354 3.469,0.563 0.594,0.208 10 false CA+ 1.063,0.646 1.438,0.99 0.375,0.344 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-29 (V-) - Body ground Always Below 1 Ω
D56-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-30 (CA+) - Body ground Ignition switch ACC 5.5 to 7.05 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL

E404549C11
5.802,1.198 6.219,1.531 0.417,0.333 4.573,3.802 4.74,4.417 4.74,4.417 4.938,4.417 false 4.156,4.396 4.292,4.396 4.292,4.396 4.469,3.854 false 4.156,1.646 4.427,0.448 4.427,0.448 4.625,0.448 true 2.031,3.906 2.198,4.521 2.198,4.521 2.396,4.521 true 1.625,4.5 1.76,4.5 1.76,4.5 1.938,3.958 true 3.563,0.365 3.698,0.365 3.698,0.365 3.979,1.667 true 3.729,3.49 4.188,3.688 0.458,0.198 10 false GND 1.198,3.5 1.656,3.698 0.458,0.198 10 false GND 1.448,4.427 1.906,4.625 0.458,0.198 10 false *d 2.438,4.427 2.896,4.625 0.458,0.198 10 false *e 3.99,4.313 4.448,4.51 0.458,0.198 10 false *d 4.948,4.333 5.406,4.531 0.458,0.198 10 false *e 4.667,0.385 5.302,0.583 0.635,0.198 10 false CGND 3.302,0.313 3.938,0.51 0.635,0.198 10 false V+ 5.885,1.281 6.25,1.51 0.365,0.229 10 false D56 1.146,0.396 1.604,0.594 0.458,0.198 10 false *a 1.125,2.781 1.583,2.979 0.458,0.198 10 false *b 3.906,2.76 4.365,2.958 0.458,0.198 10 false *c
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:
·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

·

The video waveform changes according to the image sent by the rear television camera assembly.



Item Content
Terminal No. (Symbol) D56-28 (V+) - D56-27 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.CHECK REAR TELEVISION CAMERA ASSEMBLY
5.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the television camera assembly with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL


b.

Check if the same malfunction reoccurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the D60 multi-display assembly connector.


b.

Disconnect the K4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D60,K4)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

D60-10 (CA+) - K4-6 (CB+) Always Below 1 Ω
D60-8 (V+) - K4-3 (CV+) Always Below 1 Ω
D60-9 (V-) - K4-2 (CV-) Always Below 1 Ω
D60-21 (CGND) - K4-5 (CGND) Always Below 1 Ω
D60-10 (CA+) or K4-6 (CB+) - Body ground Always 10 kΩ or higher
D60-8 (V+) or K4-3 (CV+) - Body ground Always 10 kΩ or higher
D60-9 (V-) or K4-2 (CV-) - Body ground Always 10 kΩ or higher
D60-21 (CGND) or K4-5 (CGND) - Body ground Always 10 kΩ or higher
D60-20 (CSLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MULTI-DISPLAY ASSEMBLY
a.
E367725C16
1.542,0.271 1.896,0.51 0.354,0.24 0.844,0.729 1.01,0.729 1.01,0.729 1.323,1.146 true 1.083,1.833 1.25,1.833 1.25,1.833 1.417,1.302 true 0.865,0.552 1.031,0.552 1.031,0.552 1.448,1.177 true 1.594,0.302 1.969,0.5 0.375,0.198 10 false D60 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.479,0.635 0.906,0.833 0.427,0.198 10 false CA+ 0.677,1.76 1.198,1.969 0.521,0.208 10 false CGND 0.552,0.458 0.979,0.656 0.427,0.198 10 false CV-
*a Component with harness connected
(Multi-display Assembly)


Disconnect the rear television camera assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D60)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D60-9 (CV-) - Body ground Always Below 1 Ω
D60-21 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D60)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D60-10 (CA+) - D60-21 (CGND) Ignition switch ACC 5.5 to 7.05 V
D60-10 (CA+) - D60-21 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

8.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the multi-display assembly with the connector still connected.

D223475C10
1.094,0.615 1.469,0.844 0.375,0.229 0.646,0.906 0.885,0.906 0.885,0.906 1.146,1.375 true 0.667,2.115 0.917,2.115 0.917,2.115 1.052,1.49 true 2.583,2.188 2.833,2.188 2.833,2.188 3.01,1.802 true 4.896,2.167 5.146,2.167 5.146,2.167 5.313,1.688 true 3.396,2.281 3.219,2.281 3.219,2.281 3.094,1.719 true 5.719,2.208 5.542,2.208 5.542,2.208 5.417,1.646 true 0.313,0.292 0.625,0.448 0.313,0.156 10 false *a 2.51,0.479 2.823,0.635 0.313,0.156 10 false *b 4.813,0.49 5.125,0.646 0.313,0.156 10 false *c 2.396,2.104 2.688,2.302 0.292,0.198 10 false *d 3.458,2.198 3.771,2.354 0.313,0.156 10 false *e 0.406,0.823 0.656,0.979 0.25,0.156 10 false V+ 0.219,2.042 0.75,2.344 0.531,0.302 10 false CGND 1.156,0.646 1.448,0.823 0.292,0.177 10 false D60 2.313,1.344 2.698,1.542 0.385,0.198 10 false GND 4.604,1.365 4.99,1.563 0.385,0.198 10 false GND 5.771,2.125 6.083,2.281 0.313,0.156 10 false *e 4.677,2.073 4.969,2.271 0.292,0.198 10 false *d
*a Component with harness connected
(Multi-display Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-display with the connector connected.


Item Content
Terminal No. (Symbol) D60-8 (V+) - D60-21 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK REAR TELEVISION CAMERA ASSEMBLY
9.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the television camera assembly with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL


b.

Check if the same malfunction reoccurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

NG