Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

DTC C1ABE is stored when the blind spot monitor sensor LH detects a short to ground or open in the RCTA buzzer (blind spot monitor buzzer) circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The blind spot monitor sensor is not sounding the buzzer but the buzzer receives voltage below a specified level for a specified period of time.


·

Blind spot monitor sensor LH

·

RCTA buzzer (blind spot monitor buzzer)

·

Harness or connector


Blind Spot Monitor Slave A

WIRING DIAGRAM

E329058E58
3.302,0.896 3.51,1.094 0.208,0.198 10 false 1 4.74,0.906 4.917,1.094 0.177,0.188 10 false 2 3.323,1.521 3.615,1.708 0.292,0.188 10 false G55 3.323,1.698 4.875,2.115 1.552,0.417 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.438,0.896 5.615,1.083 0.177,0.188 10 false 3 4.375,0.938 4.688,1.156 0.313,0.219 10 false BZN 3.469,0.938 3.781,1.135 0.313,0.198 10 false BZP 5.26,1.917 5.583,2.094 0.323,0.177 10 false G60 5.26,2.094 7.156,2.365 1.896,0.271 10 false Blind Spot Monitor Sensor LH 5.656,1.021 6.042,1.26 0.385,0.24 10 false BUZ 0.25,1.01 1.469,1.396 1.219,0.385 10 false from LUG-IG1 NO.1 Relay 2.052,1.219 3.115,1.49 1.063,0.271 10 false LUG-IG1 NO.2

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system and RCTA function is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Buzzer Connection State of the RCTA buzzer (blind spot monitor buzzer) Valid or Invalid Valid: Buzzer connection is valid
Invalid: Buzzer connection is invalid
-
Slave Side RCTA Function Status of the RCTA function OFF or ON OFF: RCTA function off
ON: RCTA function on
-
Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display
Buzzer Connection
Slave Side RCTA Function
50003 314 72,65
Result:
Result Proceed to
"Valid" and "ON" is displayed for all items. A
"Invalid" or "OFF" is displayed. B




A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
C1ABE is not output A
C1ABE is output B



A

B

4.CHECK HARNESS AND CONNECTOR (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] - BLIND SPOT MONITOR SENSOR LH AND BATTERY)
4.CHECK HARNESS AND CONNECTOR (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] - BLIND SPOT MONITOR SENSOR LH AND BATTERY)

Pre-procedure1

a.

Disconnect the G55 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the G60 blind spot monitor sensor LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G55,G60)Location & Routing

Click Connector(G55)Body>Floor Wire / No. 3 Floor Wire>Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer)

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G55-2 (BZN) - G60-3 (BUZ) Always Below 1 Ω
G55-2 (BZN) - Body ground Always 10 kΩ or higher



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G55)Location & Routing

Click Connector(G55)Body>Floor Wire / No. 3 Floor Wire>Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer)

G55-1 (BZP) - Body ground Ignition switch ON 11 to 14 V
G55-1 (BZP) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR