Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Buzzer does not Sound  


WIRING DIAGRAM

E329058E58
3.302,0.896 3.51,1.094 0.208,0.198 10 false 1 4.74,0.906 4.917,1.094 0.177,0.188 10 false 2 3.323,1.521 3.615,1.708 0.292,0.188 10 false G55 3.323,1.698 4.875,2.115 1.552,0.417 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.438,0.896 5.615,1.083 0.177,0.188 10 false 3 4.375,0.938 4.688,1.156 0.313,0.219 10 false BZN 3.469,0.938 3.781,1.135 0.313,0.198 10 false BZP 5.26,1.917 5.583,2.094 0.323,0.177 10 false G60 5.26,2.094 7.156,2.365 1.896,0.271 10 false Blind Spot Monitor Sensor LH 5.656,1.021 6.042,1.26 0.385,0.24 10 false BUZ 0.25,1.01 1.469,1.396 1.219,0.385 10 false from LUG-IG1 NO.1 Relay 2.052,1.219 3.115,1.49 1.063,0.271 10 false LUG-IG1 NO.2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] - BLIND SPOT MONITOR SENSOR LH AND BATTERY)

NG

2.CHECK HARNESS AND CONNECTOR (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] - BLIND SPOT MONITOR SENSOR LH AND BATTERY)
a.

Disconnect the G55 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G55,G60)Location & Routing

Click Connector(G55)Body>Floor Wire / No. 3 Floor Wire>Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer)

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G55-1 (BZP) - Body ground Ignition switch ON 11 to 14 V
G55-2 (BZN) or G60-3 (BUZ) - Body ground Below 1 V
G55-2 (BZN) - G55-1 (BZP) Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH AND BATTERY)
a.

Disconnect the G55 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the G60 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G55,G60)Location & Routing

Click Connector(G55)Body>Floor Wire / No. 3 Floor Wire>Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer)

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G55-2 (BZN) - G60-3 (BUZ) Always Below 1 Ω
G55-2 (BZN) or G60-3 (BUZ) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G55,G60)Location & Routing

Click Connector(G55)Body>Floor Wire / No. 3 Floor Wire>Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer)

Click Connector(G60)Body>Floor Wire / No. 3 Floor Wire>Blind Spot Monitor Sensor LH

G55-2 (BZN) or G60-3 (BUZ) - Body ground Ignition switch ON Below 1 V
G55-1 (BZP) - Body ground Ignition switch ON 11 to 14 V
G55-1 (BZP) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the RCTA Buzzer (Blind Spot Monitor Buzzer) with a new or known good one and check if the same malfunction recurs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSSING TRAFFIC ALERT BUZZER>REMOVAL

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

NG

REPLACE RCTA BUZZER (BLIND SPOT MONITOR BUZZER)