Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455450 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)

·

Steering lock actuator or upper bracket assembly

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

B486902E47
0.375,1.49 0.823,1.75 0.448,0.26 10 false D86 0.365,1.646 1.885,2.104 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.667,0.958 2.115,1.219 0.448,0.26 10 false LIN 4.979,1.5 5.969,1.76 0.99,0.26 10 false D24 4.969,1.667 6.969,2.219 2,0.552 10 false Steering Lock Actuator or Upper Bracket Assembly 5.208,3.313 5.656,3.573 0.448,0.26 10 false D73 5.188,3.49 6.771,3.917 1.583,0.427 10 false ID Code Box (Immobiliser Code ECU) 0.719,4.333 2.49,4.813 1.771,0.479 10 false : LIN Communication Line 5.094,2.646 5.542,2.906 0.448,0.26 10 false 2 5.094,0.792 5.542,1.052 0.448,0.26 10 false 5 1.99,0.802 2.438,1.063 0.448,0.26 10 false 13 5.292,0.948 5.74,1.208 0.448,0.26 10 false LIN 5.281,2.781 5.729,3.042 0.448,0.26 10 false LIN1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or steering lock actuator or upper bracket assembly, refer to the smart access system with push-button start (for start function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Procedure1

a.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
B2785 is output A
B2785 is not output B



Post-procedure1

a.

None



A

2.CHECK STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

B

2.CHECK STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

Pre-procedure1

a.

Disconnect the D24 steering lock actuator or upper bracket assembly connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Procedure1

a.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
B2785 is output A
B2785 is not output B



Post-procedure1

a.

None



A

3.CHECK ID CODE BOX (IMMOBILIZER CODE ECU)

B

3.CHECK ID CODE BOX (IMMOBILIZER CODE ECU)

Pre-procedure1

a.

Disconnect the D73 ID code box (immobilizer code ECU) connector.


b.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Procedure1

a.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
B2785 is output A
B2785 is not output B



Post-procedure1

a.

None



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)

B

REPLACE ID CODE BOX (IMMOBILIZER CODE ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D24 steering lock actuator or upper bracket assembly connector.


c.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D24,D73)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

Click Connector(D73)Instrument Panel>Instrument Panel Wire>ID Code Box (Immobiliser Code ECU)

D86-13 (LIN) - D24-5 (LIN) Always Below 1 Ω
D86-13 (LIN) - D73-2 (LIN1) Always Below 1 Ω
D86-13 (LIN), D24-5 (LIN) or D73-2 (LIN1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR