Home › Brake › BRAKE (REAR) › REAR BRAKE
RM37H0E _54 Brake _097303 BRAKE (REAR) _0455483 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C450053N02
5.938,1.25 6.083,1 6.083,1 6.25,1 true 2.5,4.25 2.5,3.5 true 1.365,3.354 1.531,3.354 1.531,3.354 1.729,2.99 true 0.708,3.104 0.875,3.104 0.875,3.104 1.01,2.594 true 2.125,4.25 3.208,4.25 3.208,4.25 3.208,3.938 true 3.719,4.729 3.885,4.729 3.885,4.729 4.052,4.313 true 4.583,5.229 4.719,5.229 4.719,5.229 4.844,4.802 true 4.76,0.917 4.844,0.583 4.844,0.583 5.01,0.583 true 3.792,0.583 4.125,0.583 true 6.323,0.917 6.635,1.115 0.313,0.198 10 false *1 0.5,2.969 0.865,3.333 0.365,0.365 18 false 3 1.917,4.094 2.198,4.448 0.281,0.354 18 false 1 4.396,5.104 4.677,5.458 0.281,0.354 18 false 3 3.5,4.594 3.76,4.885 0.26,0.292 18 false 2 1.135,3.208 1.427,3.51 0.292,0.302 18 false 2 3.573,0.448 3.844,0.792 0.271,0.344 18 false 4 5.083,0.448 5.354,0.792 0.271,0.344 18 false 5 0.375,3.01 0.542,3.219 0.167,0.208 10 false ● 1.792,4.135 1.958,4.344 0.167,0.208 10 false ● 4.25,5.146 4.417,5.354 0.167,0.208 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CYLINDER BOOT - (Click here) - -
2 FRONT DISC BRAKE PISTON 47831 - - -
3 PISTON SEAL - (Click here) - -
4 FRONT DISC BRAKE BLEEDER PLUG CAP 31478C - - -
5 FRONT DISC BRAKE BLEEDER PLUG 47547C - - -

*1 DISC BRAKE CYLINDER ASSEMBLY LH - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE CYLINDER BOOT

a.
C450058C01
1.875,1.208 2.24,1.5 2.24,1.5 2.406,1.5 true 0.333,0.052 1.063,0.385 0.729,0.333 18 false i, ii, iii 3.979,0.031 4.292,0.365 0.313,0.333 18 false iv 2.479,1.417 2.792,1.615 0.313,0.198 10 false *a
*a Wooden Block - -


i.

Install a wooden block between the pistons of the rear disc brake cylinder assembly LH to stop them coming out.


ii.

Using an air gun, gradually apply compressed air until the 2 rear disc brake pistons touch the wooden block.

Z101186

CAUTION:
C450059C03
2.75,1.833 2.583,1.833 2.583,1.833 2.156,1.583 true 2.844,1.75 3.042,1.906 0.198,0.156 10 false *a

·

Do not insert your hand between the pistons to hold the rear disc brake cylinder assembly LH.

·

When compressed air is blown in, the rear disc brake piston may jump out quickly and trap your fingers.




NOTICE:

Do not damage the inner surface or cylinder boot groove of the rear disc brake cylinder.



iii.

Remove the wooden block.


iv.

Remove the 2 cylinder boots from the 2 disc brake pistons and rear disc brake cylinder assembly LH.

NOTICE:

Do not damage the inner surface or cylinder boot groove of the rear disc brake cylinder.




Hide 47831 2.REMOVE REAR DISC BRAKE PISTON

a.
C450060


Hide 3.REMOVE PISTON SEAL

a.
C450061C01
3.542,1.01 4,1.333 4,1.333 4.333,1.333 true 0.406,0.042 0.688,0.396 0.281,0.354 18 false i 4.406,1.26 4.719,1.458 0.313,0.198 10 false *a
*a Protective Tape - -


i.

Using a screwdriver with its tip wrapped with protective tape, remove the 2 piston seals from the rear disc brake cylinder assembly LH.

NOTICE:

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.




Hide 31478C 4.REMOVE REAR DISC BRAKE BLEEDER PLUG CAP

a.
C450062


Hide 47547C 5.REMOVE REAR DISC BRAKE BLEEDER PLUG

a.
C450063