Home › Brake › BRAKE (REAR) › REAR BRAKE
RM37H0E _54 Brake _097303 BRAKE (REAR) _0455483 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C450066N02
5.938,1.323 6.083,1 6.083,1 6.25,1 true 3.75,0.667 4.083,0.667 true 1.229,3.333 1.396,3.333 1.396,3.333 1.604,2.958 true 0.771,1.781 0.854,1.781 0.854,1.781 1,2.167 true 2.5,4.25 3.167,4.25 3.167,4.25 3.167,4 true 3.802,4.729 3.969,4.729 3.969,4.729 4.094,4.375 true 2.75,4.25 2.75,3.417 true 5.042,4.604 5.375,4.604 true 4.677,0.917 4.917,0.5 4.917,0.5 5.083,0.5 true 6.323,0.917 6.635,1.115 0.313,0.198 10 false *1 2.177,4.115 2.542,4.438 0.365,0.323 18 false 5 3.552,0.531 3.833,0.854 0.281,0.323 18 false 2 5.427,0.375 5.698,0.708 0.271,0.333 18 false 1 5.854,4.458 6.219,4.781 0.365,0.323 18 false 3 0.542,1.656 0.885,1.948 0.344,0.292 18 false 3 1.052,3.198 1.417,3.521 0.365,0.323 18 false 4 3.615,4.604 3.979,4.927 0.365,0.323 18 false 4 5.688,4.5 5.844,4.698 0.156,0.198 10 false ● 0.385,1.698 0.542,1.896 0.156,0.198 10 false ● 2,4.167 2.156,4.365 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC BRAKE BLEEDER PLUG 47547C (Click here) - -
2 REAR DISC BRAKE BLEEDER PLUG CAP 31478C - - -
3 PISTON SEAL - (Click here) - -
4 REAR DISC BRAKE PISTON - (Click here) - -
5 CYLINDER BOOT 47831 (Click here) - -

● Non-reusable part
V100135

Lithium soap base glycol grease

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47547C 1.TEMPORARILY INSTALL REAR DISC BRAKE BLEEDER PLUG

Z101186

HINT:

Tighten the rear disc brake bleeder plug after bleeding the system.



Hide 31478C 2.INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.
C450067C01
0.167,0.052 0.333,0.333 0.167,0.281 18 false i 3.99,0.042 4.333,0.333 0.344,0.292 18 false ii
V100155

Lithium soap base glycol grease - -


i.

Apply lithium soap base glycol grease to the entire circumference of 2 new piston seals.


ii.

Install the 2 piston seals to the rear disc brake cylinder assembly LH.

NOTICE:

Do not damage the piston seal.




Hide 47831 4.INSTALL REAR DISC BRAKE PISTON

a.
C450068C02
1.667,0.833 2.01,0.833 true 1.667,1.917 2.156,1.917 true 0.448,0.052 1.208,0.417 0.76,0.365 18 false i - iii 1.49,0.771 1.677,0.948 0.188,0.177 10 false *1 1.469,1.844 1.698,2.073 0.229,0.229 10 false *2
*1 Cylinder Boot *2 Rear Disc Brake Piston
V100155

Lithium soap base glycol grease - -


i.

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new cylinder boots.


ii.

Install the 2 cylinder boots to the rear disc brake pistons.

NOTICE:

Securely install the cylinder boot into the groove of the rear disc brake piston.



iii.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake pistons, and install it to the rear disc brake cylinder assembly LH.

NOTICE:

Do not forcibly install the rear disc brake piston into the rear disc brake cylinder assembly LH.




Hide 5.INSTALL CYLINDER BOOT

a.
C450069C01
2.583,2 2.396,2 2.396,2 2.396,1.656 true 1.667,0.75 1.5,0.75 1.5,0.75 1.5,1.094 true 3,0.875 2.833,0.875 2.833,0.875 2.833,1.292 true 2.656,1.927 2.885,2.167 0.229,0.24 10 false *1 1.729,0.688 2.042,0.844 0.313,0.156 10 false *2 0.417,0.042 0.833,0.396 0.417,0.354 18 false i 3.042,0.802 3.323,1.052 0.281,0.25 10 false *3
*1 Cylinder Boot *2 Rear Disc Brake Piston
*3 Rear Disc Brake Cylinder Assembly LH - -


Install the 2 cylinder boots to the rear disc brake cylinder assembly LH as shown in the illustration.

NOTICE:
·

Securely install the cylinder boot into the groove of the rear disc brake cylinder assembly LH and rear disc brake piston.

·

Do not damage the cylinder boot.