Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM37H0E _54 Brake _097302 BRAKE (FRONT) _0455487 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C437782N01
2.823,2.583 3.031,2.583 3.031,2.583 3.031,4.917 false 2.813,3.75 3.031,3.75 true 4.458,3.583 4.667,3.583 4.667,3.583 4.667,5.083 true 3.625,4.25 3.844,4.25 true 3.635,3.104 3.844,3.104 3.844,3.104 3.844,5.104 true 5.24,5.146 5.833,5.146 true 2,2.167 2.167,2.167 2.167,2.167 2.167,4.167 true 2,3.333 2.167,3.333 true 5.229,3.979 5.563,3.979 5.563,3.979 5.563,5.146 true 4.448,4.75 4.667,4.75 true 0.833,1.667 0.333,1.667 0.333,1.667 0.333,3.417 true 0.333,2.833 0.823,2.833 true 4.781,0.333 4.5,0.333 true 5.333,0.594 5.5,0.333 5.5,0.333 5.667,0.333 true 6.156,0.896 6.323,0.635 6.323,0.635 6.49,0.635 true 3.188,5.021 3.458,5.25 0.271,0.229 10 false ● 4,5.177 4.271,5.406 0.271,0.229 10 false ● 3.375,4.938 3.656,5.292 0.281,0.354 18 false 1 4.167,5.094 4.448,5.448 0.281,0.354 18 false 1 4.604,5.104 4.917,5.51 0.313,0.406 18 false 2 2.115,4.177 2.427,4.479 0.313,0.302 18 false 2 6.146,5.063 6.417,5.292 0.271,0.229 10 false ● 6.333,4.979 6.646,5.344 0.313,0.365 18 false 3 0.479,3.5 0.75,3.729 0.271,0.229 10 false ● 0.688,3.417 1,3.781 0.313,0.365 18 false 3 4.302,0.208 4.615,0.542 0.313,0.333 18 false 4 5.76,0.177 6.083,0.5 0.323,0.323 18 false 5 6.583,0.552 6.813,0.781 0.229,0.229 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CYLINDER BOOT - (Click here) - -
2 FRONT DISC BRAKE PISTON 47731 - - -
3 PISTON SEAL - (Click here) - -
4 FRONT DISC BRAKE BLEEDER PLUG CAP 31478B - - -
5 FRONT DISC BRAKE BLEEDER PLUG 47547B - - -

*1 DISC BRAKE CYLINDER ASSEMBLY LH - -
● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE CYLINDER BOOT

a.
C437784C01
1.583,1.5 1.75,1.5 1.75,1.5 2.135,1.333 false 1.375,1.427 1.688,1.625 0.313,0.198 10 false *a 0.417,0.042 1.323,0.375 0.906,0.333 18 false i, ii, iii 3.969,0.021 4.271,0.313 0.302,0.292 18 false iv
*a Wooden Block - -


i.

Install a wooden block between the pistons of the disc brake cylinder assembly LH to stop them coming out.


ii.

Using an air gun, gradually apply compressed air until the 4 front disc brake pistons touch the wooden block.

Z101186

CAUTION:
·
C437785

Do not insert your hand between the pistons to hold the disc brake cylinder assembly LH.

·

When compressed air is blown in, the front disc brake piston may jump out quickly and trap your fingers.




NOTICE:

Do not allow any brake fluid to spatter.



iii.

Remove the Wooden block.


iv.

Remove the 4 cylinder boots from the disc brake cylinder assembly LH and front disc brake pistons.

NOTICE:

Be careful not to damage the disc brake cylinder assembly LH and front disk brake pistons.




Hide 47731 2.REMOVE FRONT DISC BRAKE PISTON

a.
C437786


Hide 3.REMOVE PISTON SEAL

a.
C437787C01
3.917,1.031 3.583,0.5 3.583,0.5 3.417,0.5 true 0.417,0.031 0.698,0.385 0.281,0.354 18 false i 3.167,0.396 3.375,0.604 0.208,0.208 10 true *a
*a Protective Tape - -


i.

Using a screwdriver with its tip wrapped with protective tape, remove the 4 piston seals from the disc brake cylinder assembly LH.

NOTICE:

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.




Hide 31478B 4.REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP

a.
C437788


Hide 47547B 5.REMOVE FRONT DISC BRAKE BLEEDER PLUG

a.
C437789