Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM37H0E _54 Brake _097302 BRAKE (FRONT) _0455487 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C455187C01
2.823,2.583 3.031,2.583 3.031,2.583 3.031,4.917 false 2.813,3.75 3.031,3.75 true 4.458,3.583 4.667,3.583 4.667,3.583 4.667,5.333 true 3.625,4.25 3.844,4.25 true 3.635,3.104 3.844,3.104 3.844,3.104 3.844,5.104 true 5.25,5.146 5.833,5.146 true 1.917,2.167 2.083,2.167 2.083,2.167 2.083,4.167 true 1.917,3.333 2.083,3.333 true 5.24,3.979 5.573,3.979 5.573,3.979 5.573,5.146 true 4.448,4.75 4.667,4.75 true 0.833,1.667 0.333,1.667 0.333,1.667 0.333,3.417 true 0.333,2.833 0.823,2.833 true 4.781,0.333 4.5,0.333 true 5.333,0.604 5.583,0.333 5.583,0.333 5.75,0.333 true 6.667,0.833 6.5,0.833 6.5,0.833 6.302,1.063 true 2.854,5 3.125,5.229 0.271,0.229 10 false ● 3.646,5.198 3.917,5.427 0.271,0.229 10 false ● 3,4.948 3.281,5.302 0.281,0.354 18 false 5 3.802,5.146 4.083,5.5 0.281,0.354 18 false 5 4.646,5.365 4.958,5.771 0.313,0.406 18 false 4 2.042,4.208 2.354,4.51 0.313,0.302 18 false 4 6.135,5.052 6.406,5.281 0.271,0.229 10 false ● 6.281,5 6.594,5.365 0.313,0.365 18 false 3 0.469,3.479 0.74,3.708 0.271,0.229 10 false ● 0.625,3.427 0.938,3.792 0.313,0.365 18 false 3 4.25,0.177 4.563,0.51 0.313,0.333 18 false 2 6.063,0.177 6.385,0.5 0.323,0.323 18 false 1 6.75,0.76 7.063,0.958 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG 47547B (Click here) - -
2 FRONT DISC BRAKE BLEEDER PLUG CAP 31478B - - -
3 PISTON SEAL - (Click here) - -
4 FRONT DISC BRAKE PISTON 47731 (Click here) - -
5 CYLINDER BOOT - (Click here) - -

*1 DISC BRAKE CYLINDER ASSEMBLY LH - -
● Non-reusable part
V100135

Lithium soap base glycol grease

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47547B 1.TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG

Z101186

HINT:

Fully tighten the front disc brake bleeder plug after bleeding the system.



Hide 31478B 2.INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.
C437792C01
3.979,0.042 4.344,0.427 0.365,0.385 18 false ii 0.406,0.031 0.802,0.375 0.396,0.344 18 false i
V100155

Lithium soap base glycol grease - -


i.

Apply lithium soap base glycol grease to the entire circumference of 4 new piston seals.


ii.

Install the 4 piston seals to the disc brake cylinder assembly LH.

NOTICE:

Securely install the piston seal into the groove of the disc brake cylinder assembly LH.




Hide 47731 4.INSTALL FRONT DISC BRAKE PISTON

a.
C437793C03
1.615,0.833 1.865,0.833 true 1.667,1.75 2,1.75 true 0.396,0.042 1.115,0.365 0.719,0.323 18 false i - iii 1.417,0.75 1.729,0.948 0.313,0.198 10 false *1 1.458,1.688 1.667,1.917 0.208,0.229 10 false *2
*1 Cylinder Boot *2 Front Disc Brake Piston
V100155

Lithium soap base glycol grease - -


i.

Apply a light layer of lithium soap base glycol grease to the entire circumference of 4 new cylinder boots.


ii.

Install the 4 cylinder boots to the front disc brake pistons.

NOTICE:

Securely install the cylinder boot into the groove of the front disc brake piston.



iii.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the front disc brake pistons, and install it to the disc brake cylinder assembly LH.

NOTICE:

Do not forcibly install the front disc brake piston into the disc brake cylinder assembly LH.




Hide 5.INSTALL CYLINDER BOOT

a.
C437794C01
2,0.833 1.833,0.833 1.833,0.833 1.667,1.083 true 2.375,1.667 2.375,2 2.375,2 2.542,2 true 2.917,0.917 2.833,0.917 2.833,0.917 2.833,1.333 true 2.604,1.927 2.917,2.083 0.313,0.156 10 false *1 2.083,0.76 2.396,0.917 0.313,0.156 10 false *2 2.99,0.854 3.281,1.094 0.292,0.24 10 false *3 0.417,0.042 0.729,0.406 0.313,0.365 18 false i
*1 Cylinder Boot *2 Front Disc Brake Piston
*3 Disc Brake Cylinder Assembly LH - -


i.

Install the 4 cylinder boots to the disc brake cylinder assembly LH as shown in the illustration.

NOTICE:
·

Securely install the cylinder boot into the groove of the disc brake cylinder assembly LH and front disc brake piston.

·

Do not damage the cylinder boot.