Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › PRE-COLLISION SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0455731 PRE-COLLISION SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  PRE-COLLISION SYSTEM  U023A87  Lost Communication with Image Processing Module "A" Missing Message  


DESCRIPTION

The forward recognition camera communicates with the No. 2 skid control ECU (brake actuator assembly) via CAN communication.

If a communication error is detected between the No. 2 skid control ECU (brake actuator assembly) and forward recognition camera, the forward recognition camera stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U023A87 Lost Communication with Image Processing Module "A" Missing Message When the ignition switch is ON for 2 seconds or more, a communication malfunction between the No. 2 skid control ECU (brake actuator assembly) and the forward recognition camera is detected for approximately 3 seconds or more.
·

Electronically controlled brake system

·

Forward recognition camera


Pre-Collision System B

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs (Brake/EPB)
a.

Using the GTS, check for electronically controlled brake system DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:

If DTC U023A87 and electronically controlled brake system DTCs are output, perform troubleshooting for the electronically controlled brake system first.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.PERFORM DEALER MODE (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.PERFORM DEALER MODE (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

When entering Dealer Mode (Signal Check), the No. 2 skid control ECU (brake actuator assembly) communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Signal Check) within 5 seconds of entering Dealer Mode (Signal Check).


Pre-procedure1

a.

None


Procedure1

a.

Procedure to Enter Dealer Mode (Signal Check)

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

Check that park (P) is selected.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Switch the skid control ECU to Dealer Mode (Signal Check) using the GTS.

Chassis > Brake/EPB > Utility
Tester Display
Signal Check
50005 435 4558
HINT:

After entering Dealer Mode (Calibration), maintain Dealer Mode (Calibration) condition for 5 seconds. If Dealer Mode (Calibration) is ended before 5 seconds elapse, enter Dealer Mode (Calibration) again, wait 5 seconds, and then check for DTCs again.




b.

Confirm the system has entered Dealer Mode (Signal Check)

i.

Confirm that the ABS warning light, brake system warning light (yellow indicator) and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 second intervals).

HINT:
·

When in Dealer Mode (signal check), "Traction Control Turned Off" is displayed on the multi-information display.

·

When entering Dealer Mode (Signal Check), if the parking brake is engaged, the parking brake indicator light (red) will illuminate, and if the parking brake is not engaged, the parking brake indicator light (red) will blink in the Dealer Mode pattern (blinking at 0.25 second intervals).



Result:
Proceed to
NEXT




Post-procedure1

a.

End of Dealer Mode (Signal Check)

i.

Turn the ignition switch off.


ii.

Disconnect the GTS.




NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

4.CHECK FOR DTCs
4.CHECK FOR DTCs

Pre-procedure1

a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



Procedure1

a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Result:
Result Proceed to
U023A87 is not output A
U023A87 is output B



Post-procedure1

a.

None



A

END

B

REPLACE FORWARD RECOGNITION CAMERA