Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448284 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B604646N02
4.635,3.094 4.385,3.094 false 3.698,1 3.938,0.542 3.938,0.542 5.052,0.542 true 6.177,2.208 6.063,2.458 6.063,2.458 5.677,2.458 true 2,1.688 2.75,1.688 2.75,1.688 2.896,1.51 true 0.948,2.219 1.042,2.469 1.042,2.469 1.438,2.469 true 1.958,1.25 2.708,1.25 2.708,1.25 2.875,1.417 true 6.24,4 5.885,4 false 1.417,3.99 1.073,3.99 false 5.031,4.49 4.677,4.49 false 5.375,1.677 4.49,1.677 4.49,1.677 4.375,1.5 true 1.583,3.365 1.25,3.365 false 4.969,3 5.438,3.271 0.469,0.271 10 false (1) ● 6.552,3.896 7.01,4.167 0.458,0.271 10 false (3) ● 0.531,3.906 0.969,4.167 0.438,0.26 10 false (2) ● 5.292,2.948 5.573,3.302 0.281,0.354 18 false 1 0.885,3.854 1.167,4.208 0.281,0.354 18 false 2 6.885,3.844 7.073,4.198 0.188,0.354 18 false 3 5.115,0.448 5.573,0.646 0.458,0.198 10 false (1) 1.781,1.604 2.01,2 0.229,0.396 10 false (2) 5.427,1.594 5.656,1.865 0.229,0.271 10 false (3) 1.51,2.385 1.969,2.583 0.458,0.198 10 false (5) 5.49,2.375 5.948,2.573 0.458,0.198 10 false (5) 0.719,3.292 1.26,3.646 0.542,0.354 10 false (4) ● 5.708,4.344 5.896,4.698 0.188,0.354 18 false 5 1.771,1.156 2,1.427 0.229,0.271 10 true (4) 1.063,3.229 1.25,3.583 0.188,0.354 18 false 4 5.375,4.396 5.948,4.635 0.573,0.24 10 false (5) ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SYMBOL EMBLEM 75741E (Click here) - -
2 NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE 75442 (Click here) - -
3 NO. 3 LUGGAGE COMPARTMENT DOOR PLATE 75443A (Click here) - -
4 REAR NO. 1 NAME PLATE 75441 (Click here) - -
5 ROCKER PANEL MOULDING EMBLEM 75374A (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 75741E 1.INSTALL SYMBOL EMBLEM

a.
B599559C01
2.698,2.427 4.198,2.427 4.198,2.427 4.198,1.26 true 3.229,2.417 3.229,1.5 true 5.531,0.281 5.813,0.635 0.281,0.354 18 false i 5.521,1.438 5.802,1.792 0.281,0.354 18 false ii 3.563,0.063 3.771,0.344 0.208,0.281 18 true iii 2.573,2.354 2.771,2.594 0.198,0.24 10 true *a
*a Boss Position - -


i.

Clean the surface of the luggage compartment door outside garnish sub-assembly.

1. Using a heat light, heat the luggage compartment door outside garnish sub-assembly surface.

Standard Value:
Part Temperature
Luggage Compartment Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)
Symbol Emblem 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the luggage compartment door outside garnish sub-assembly excessively.


2. Remove any remaining double-sided tape from the luggage compartment door outside garnish sub-assembly.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the symbol emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the luggage compartment door outside garnish sub-assembly and a new symbol emblem.

NOTICE:

Do not heat the luggage compartment door outside garnish sub-assembly and symbol emblem excessively.



iii.

Align the boss positions and install the symbol emblem.

NOTICE:

The application strength of the symbol emblem will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the luggage compartment door outside garnish sub-assembly.




Hide 75442 2.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.
B599563C02
4.313,2.125 4.615,2.438 true 2.594,0.083 3.104,0.333 0.51,0.25 10 true *a 4.083,0.521 4.219,0.688 0.135,0.167 10 true A 2.979,0.802 3.115,0.969 0.135,0.167 10 true B 3.198,1.625 3.333,1.792 0.135,0.167 10 true C 5.427,1.802 5.563,1.969 0.135,0.167 10 true D 0.604,0.271 0.885,0.625 0.281,0.354 18 false i 0.573,1.438 0.854,1.792 0.281,0.354 18 false ii 2.865,0.073 3.146,0.427 0.281,0.354 18 false iii 4.542,2.469 4.865,2.729 0.323,0.26 10 true *b
*a Reference Values *b Luggage Compartment Door Panel Edge Line


Standard Measurement:
Area Measurement Area Measurement
A 204.3 mm (8.04 in.) B 58.8 mm (2.31 in.)
C 50.2 mm (1.98 in.) D 40.5 mm (1.59 in.)


i.

Clean the surface of the luggage compartment door panel.

1. Using a heat light, heat the luggage compartment door panel surface.

Standard Value:
Part Temperature
Luggage Compartment Door Panel 40 to 60°C (104 to 140°F)
No. 2 Luggage Compartment Door Name Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the luggage compartment door panel excessively.


2. Remove any remaining double-sided tape from the luggage compartment door panel.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 2 luggage compartment door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the luggage compartment door panel and a new No. 2 luggage compartment door name plate.

NOTICE:

Do not heat the luggage compartment door panel and No. 2 luggage compartment door name plate excessively.



iii.

Install the No. 2 luggage compartment door name plate as shown in the illustration.

NOTICE:

The application strength of the No. 2 luggage compartment door name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the luggage compartment door panel.




Hide 75443A 3.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR PLATE

a.
B599569C02
4.125,1.875 3.615,2.531 true 0.594,0.281 0.875,0.635 0.281,0.354 18 false i 0.563,1.427 0.844,1.781 0.281,0.354 18 false ii 2.948,0.052 3.594,0.354 0.646,0.302 10 true *a 4.469,0.542 4.646,0.688 0.177,0.146 10 true A 5.198,0.969 5.375,1.115 0.177,0.146 10 true B 5.135,1.5 5.281,1.656 0.146,0.156 10 true C 3.594,1.635 3.729,1.781 0.135,0.146 10 true D 3.49,2.5 3.698,2.667 0.208,0.167 10 true *b 3.146,0.031 3.427,0.385 0.281,0.354 18 false iii
*a Reference Values *b Luggage Compartment Door Panel Edge Line


Standard Measurement:
Area Measurement Area Measurement
A 206.1 mm (8.11 in.) B 77.0 mm (3.03 in.)
C 56.4 mm (2.22 in.) D 41.2 mm (1.62 in.)


i.

Clean the surface of the luggage compartment door panel.

1. Using a heat light, heat the luggage compartment door panel surface.

Standard Value:
Part Temperature
Luggage Compartment Door Panel 40 to 60°C (104 to 140°F)
No. 3 Luggage Compartment Door Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the luggage compartment door panel excessively.


2. Remove any remaining double-sided tape from the luggage compartment door panel.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 3 luggage compartment door plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the luggage compartment door panel and a new No. 3 luggage compartment door plate.

NOTICE:

Do not heat the luggage compartment door panel and No. 3 luggage compartment door plate excessively.



iii.

Install the No. 3 luggage compartment door plate as shown in the illustration.

NOTICE:

The application strength of the No. 3 luggage compartment door plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the luggage compartment door panel.




Hide 75441 4.INSTALL REAR NO. 1 NAME PLATE

a.
B599561C01
4.313,2.135 4.615,2.448 true 2.594,0.083 3.104,0.333 0.51,0.25 10 true *a 3.594,0.521 3.729,0.688 0.135,0.167 10 true A 3.01,0.802 3.146,0.969 0.135,0.167 10 true B 3.333,1.531 3.469,1.698 0.135,0.167 10 true C 4.677,1.646 4.813,1.813 0.135,0.167 10 true D 0.604,0.271 0.885,0.625 0.281,0.354 18 false i 0.573,1.438 0.854,1.792 0.281,0.354 18 false ii 2.865,0.073 3.146,0.427 0.281,0.354 18 false iii 4.542,2.448 4.865,2.708 0.323,0.26 10 true *b
*a Reference Values *b Luggage Compartment Door Panel Edge Line


Standard Measurement:
Area Measurement Area Measurement
A 151.4 mm (5.96 in.) B 74.7 mm (2.94 in.)
C 72.3 mm (2.85 in.) D 62.2 mm (2.45 in.)


i.

Clean the surface of the luggage compartment door panel.

1. Using a heat light, heat the luggage compartment door panel surface.

Standard Value:
Part Temperature
Luggage Compartment Door Panel 40 to 60°C (104 to 140°F)
Rear No. 1 Name Plate 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the luggage compartment door panel excessively.


2. Remove any remaining double-sided tape from the luggage compartment door panel.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear No. 1 name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the luggage compartment door panel and a new rear No. 1 name plate.

NOTICE:

Do not heat the luggage compartment door panel and rear No. 1 name plate excessively.



iii.

Install the rear No. 1 name plate as shown in the illustration.

NOTICE:

The application strength of the rear No. 1 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the luggage compartment door panel.




Hide 75374A 5.INSTALL ROCKER PANEL MOULDING EMBLEM

a.
B599666C03
0.073,0.073 0.385,0.271 0.313,0.198 12 false *A 0.104,2.896 0.417,3.094 0.313,0.198 12 false *B 0.896,0.333 1.177,0.688 0.281,0.354 18 false i 5.635,3.167 5.917,3.521 0.281,0.354 18 false i 0.875,1.5 1.156,1.854 0.281,0.354 18 false ii 5.625,4.333 5.906,4.688 0.281,0.354 18 false ii 3.385,0.219 3.865,0.438 0.479,0.219 10 true *a 3.656,0.198 3.938,0.552 0.281,0.354 18 false iii 2.615,3.073 3.094,3.292 0.479,0.219 10 true *a 2.833,3.073 3.115,3.427 0.281,0.354 18 false iii 4.021,0.552 4.177,0.698 0.156,0.146 10 true A 5.219,1.208 5.375,1.354 0.156,0.146 10 true B 3.375,1.281 3.5,1.406 0.125,0.125 10 true C 3.448,1.615 3.573,1.74 0.125,0.125 10 true D 3.344,3.458 3.469,3.583 0.125,0.125 10 true E 2.26,4.083 2.354,4.198 0.094,0.115 10 true F 4.125,4.156 4.25,4.292 0.125,0.135 10 true G 4,4.5 4.125,4.635 0.125,0.135 10 true H
*A for LH Side *B for RH Side
*a Reference Values - -


Standard Measurement:
Area Measurement Area Measurement
A 197.4 mm (7.77 in.) B 19.7 mm (0.776 in.)
C 41.0 mm (1.61 in.) D 42.8 mm (1.69 in.)
E 212.8 mm (8.38 in.) F 22.4 mm (0.882 in.)
G 41.1 mm (1.62 in.) H 61.7 mm (2.43 in.)


i.

Clean the surface of the rocker panel moulding.

1. Using a heat light, heat the rocker panel moulding surface.

Standard Value:
Part Temperature
Rocker Panel Moulding 20 to 30°C (68 to 86°F)
Rocker Panel Moulding Emblem 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rocker panel moulding excessively.


2. Remove any remaining double-sided tape from the rocker panel moulding.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rocker panel moulding emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the rocker panel moulding and a new rocker panel moulding emblem.

NOTICE:

Do not heat the rocker panel moulding and rocker panel moulding emblem excessively.



iii.

Install the 2 rocker panel moulding emblem as shown in the illustration.

NOTICE:

The application strength of the rocker panel moulding emblem will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the rocker panel moulding.