Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C110E14  Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 1 skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the main relay, the No. 1 skid control ECU (brake booster with master cylinder assembly) will store a DTC.

If the auxiliary battery voltage is temporarily low, this DTC may be stored.

HINT:

DTC C125600 may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C110E14 Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open When the voltage at terminal +BI1 is more than 7.3 V, the voltage at terminal MRI1 is less than 5.7 V for 1 second or more.
·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427346E09
0.375,1.844 1.625,2.208 1.25,0.365 10 false ABS-MAIN 0.26,2.958 1.625,3.26 1.365,0.302 10 false ABS MAIN NO. 1 0.385,0.729 1.188,1.083 0.802,0.354 10 false ABS MTR 0.281,4.104 1.458,4.375 1.177,0.271 10 false AHB ECU-IG1 0.313,5.208 1.354,5.458 1.042,0.25 10 false IG2 D NO. 3 4.26,1.531 4.573,1.729 0.313,0.198 10 false 15 4.271,2.656 4.583,2.854 0.313,0.198 10 false 14 4.344,0.427 4.656,0.625 0.313,0.198 10 false 1 4.281,3.781 4.594,3.979 0.313,0.198 10 false 31 4.281,4.896 4.594,5.094 0.313,0.198 10 false 42 4.573,1.792 4.885,1.99 0.313,0.198 10 false BS 4.552,2.906 5,3.188 0.448,0.281 10 false +BI1 4.563,0.677 4.99,0.938 0.427,0.26 10 false MRI1 4.563,4.021 4.875,4.219 0.313,0.198 10 false IG1 4.563,5.146 4.875,5.344 0.313,0.198 10 false IG2 4.406,5.688 4.719,5.885 0.313,0.198 10 false A5 4.406,5.865 6.823,6.292 2.417,0.427 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.885,2.781 6.198,2.979 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
Only C110E14 is output A
C110E14 and other DTCs are output B



A

2.CHECK DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-14 (+BI1) - Body ground Always 11 to 14 V
A5-1 (MRI1) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR