Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050023  Left Front Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050012.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050023 Left Front Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Speed sensor installation

·

Wire harness and connector

·

Front speed sensor LH (front axle hub sub-assembly LH)

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Front skid control sensor wire LH


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C050023 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) - - ○
Detection Time 15 seconds or more. 1 second or more. 15 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C210569C06
2.344,1.854 2.656,2.052 0.313,0.198 10 *b 0.958,1.833 1.271,2.031 0.313,0.198 10 *a
*a Correct
*b Incorrect


Check the front speed sensor LH installation.

OK:

There is no clearance between the front speed sensor LH and the front steering knuckle LH.


HINT:

The front speed sensor LH and front speed sensor rotor LH are incorporated into the front axle hub sub-assembly LH.

If the front speed sensor LH and front speed sensor rotor LH need to be replaced, replace the front axle hub sub-assembly LH.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FL WHEEL SPEED)

NG

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

2.READ VALUE USING GTS (FL WHEEL SPEED)

Pre-procedure1

a.

Perform a road test.


Procedure1

a.

Check the front speed sensor LH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
50003 435 14
OK:

The output value changes in accordance with the vehicle speed.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

3.INSPECT FRONT SKID CONTROL SENSOR WIRE LH
3.INSPECT FRONT SKID CONTROL SENSOR WIRE LH

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the AW1 front skid control sensor wire LH connector.


b.

Disconnect the W1 front skid control sensor wire LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(W1,AW1)Location & Routing

Click Connector(W1)Engine Compartment>Front Skid Control Sensor Wire LH / Front Skid Control Sensor Wire RH>Front Speed Sensor LH (Front Axle Hub Sub-Assembly LH)

Click Connector(AW1)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire LH

W1-2 (FL+) - AW1-3 Always Below 1 Ω
W1-2 (FL+) or AW1-3 - Body ground and other terminals Always 10 kΩ or higher
W1-1 (FL-) - AW1-1 Always Below 1 Ω
W1-1 (FL-) or AW1-1 - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE FRONT SKID CONTROL SENSOR WIRE LH

4.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU(brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(AW1,A6)Location & Routing

Click Connector(AW1)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire LH

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

AW1-3 - A6-22 (FL+) Always Below 1 Ω
AW1-3 or A6-22 (FL+) - Body ground Always 10 kΩ or higher
AW1-1 - A6-21 (FL-) Always Below 1 Ω
AW1-1 or A6-21 (FL-) - Body ground Always 10 kΩ or higher


HINT:

The front speed sensor rotor LH and front speed sensor LH are incorporated into the front axle hub sub-assembly LH.

If the front speed sensor LH and front speed sensor rotor LH needs to be replaced, replace the front axle hub sub-assembly LH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR