Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM37H0E _52 Drivetrain _095769 AXLE AND DIFFERENTIAL _0452037 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446752N03
6.615,0.177 6.885,0.177 true 6.667,5.167 6.5,5.167 6.5,5.167 6.375,4.885 true 6.115,2.083 5.948,2.083 5.948,2.083 5.729,2.49 true 2.667,1.583 2.5,1.583 2.5,1.583 2.292,2 true 4.583,3.823 4.417,3.823 4.417,3.823 4.313,3.625 true 3,3.333 3.167,3.333 3.167,3.333 3.313,3.083 true 1.083,2.979 1.417,2.979 true 2.979,1.99 2.802,1.99 2.802,1.99 2.729,2.25 true 6.625,0.625 6.833,0.625 true 5,2.167 5.083,2.167 5.083,2.167 5.292,2.385 true 6.406,0.042 6.688,0.396 0.281,0.354 18 false 1 6.406,0.479 6.688,0.833 0.281,0.354 18 false 2 1.49,2.854 1.771,3.208 0.281,0.354 18 false 4 6.729,5.042 7.01,5.396 0.281,0.354 18 false 3 6.448,1.969 6.729,2.323 0.281,0.354 18 false 5 4.906,3.677 5.188,4.031 0.281,0.354 18 false 6 2.823,3.188 3.104,3.542 0.281,0.354 18 false 7 3.042,1.833 3.323,2.188 0.281,0.354 18 false 8 5.344,1.708 5.656,1.906 0.313,0.198 10 false x 2 4.115,1.667 4.427,1.865 0.313,0.198 10 false x 3 1.031,0.563 1.344,0.76 0.313,0.198 10 false x 4 4.792,2.094 5.021,2.323 0.229,0.229 10 false *1 2.74,1.448 3.021,1.802 0.281,0.354 18 false 9 4.76,2.698 5.073,2.896 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 FRONT WHEEL - - - -
4 FRONT SKID CONTROL SENSOR WIRE LH 89516F - - -
5 DISC BRAKE CYLINDER ASSEMBLY LH 47750 (Click here) - -
6 FRONT DISC LH 43512 (Click here) -
7 FRONT DISC BRAKE DUST COVER LH 47782 - - -
8 FRONT AXLE HUB SUB-ASSEMBLY LH 43502C - - -
9 DISC BRAKE AIR GUIDE PLATE 47791B - - -

*1 FRONT NO. 2 FLEXIBLE HOSE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 89516F 4.DISCONNECT FRONT SKID CONTROL SENSOR WIRE LH

a.
C446753


Hide 47750 5.DISCONNECT DISC BRAKE CYLINDER ASSEMBLY LH

a.
C449440N01
1.906,2.49 2.167,2.667 2.167,2.667 2.417,2.667 true 0.26,0.073 0.698,0.427 0.438,0.354 18 false i 3.906,0.094 4.188,0.396 0.281,0.302 18 true ii 0.229,2 0.51,2.354 0.281,0.354 18 false iii 3.927,2.01 4.427,2.323 0.5,0.313 18 true iv, v 2.479,2.583 2.906,2.802 0.427,0.219 10 true SST

i.

Remove the 2 bolts and disconnect the No. 2 front flexible hose from the front flexible hose bracket LH and No. 2 front flexible hose bracket LH.


ii.

Loosen the bolts on the lower side of the disc brake cylinder assembly LH and remove the bolts on the top side.

NOTICE:

Do not excessively loosen the bolts on the lower side of the disc brake cylinder assembly LH.



iii.

Tilt the disc brake cylinder assembly LH and install SST as shown in the illustration.

SST
09727-00110  


iv.

Install SST to the front upper No. 2 suspension arm assembly LH.

NOTICE:

The front upper No. 2 suspension arm assembly LH may become damaged if the metal part of SST contacts it. Therefore, install it so that the metal part does not contact the front upper No. 2 suspension arm assembly LH.



v.

Remove the bolt on the lower side of the disc brake cylinder assembly LH and disconnect it.

NOTICE:
·

Do not apply excessive force to the flexible hose.

·

If there is no looseness in the flexible hose, adjust the length of SST.





Hide 43512 6.REMOVE FRONT DISC

Z101186

Click here(Click here)

Hide 47782 7.REMOVE FRONT DISC BRAKE DUST COVER LH

a.
C446755


Hide 43502C 8.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

a.
C446756


Hide 47791B 9.REMOVE DISC BRAKE AIR GUIDE PLATE

a.
C446757