Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C134551  Linear Solenoid Valve Offset Learning Not Programmed  C134554  Linear Solenoid Valve Offset Learning Missing Calibration  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) stores the individual characteristics of each linear solenoid built into the brake booster with master cylinder assembly. Based on the stored information, the No. 1 skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The No. 2 skid control ECU (brake actuator assembly) receives the shift position P signal from the EV control ECU via CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C134551 Linear Solenoid Valve Offset Learning Not Programmed The linear solenoid valve offset learning value is not stored.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

During Dealer Mode, related DTCs are cleared.


C134554 Linear Solenoid Valve Offset Learning Missing Calibration The linear solenoid valve offset learning value cannot be obtained.
·

Perform linear solenoid valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no DTCs other than those related to incomplete learning are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
OK:

DTCs other than those related to incomplete learning are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM AIR BLEEDING

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.PERFORM AIR BLEEDING
HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
3.PERFORM LINEAR SOLENOID VALVE OFFSET LEARNING
a.

Check and ensure the following conditions required for performing linear solenoid valve offset learning and then perform linear solenoid valve offset learning.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


NOTICE:

If DTC C134554 is output, wait 3 minutes or more with the ignition switch turned off, then perform learning after turning the ignition switch to ON and clearing the DTCs.


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch is ON (READY).

2.

The brake booster with master cylinder assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that park (P) is selected.

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.

8.

DTC C145151 is not output. (If it is output, bleed the air from the high-pressure tube.)



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
C134551 and C134554 are not output A
C134551 or C134554 is output B



Post-procedure1

a.

None



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY