Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The airbag ECU assembly has a built-in yaw rate and acceleration sensor.

This DTC is stored when the No. 2 skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (airbag ECU assembly).

This DTC may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed exceeding 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness and connector

·

Acceleration sensor (airbag ECU assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C443739E06
0.781,1.323 1.396,1.521 0.615,0.198 10 false CAFH 6.063,1.323 6.677,1.521 0.615,0.198 10 false CANH 0.802,0.708 1.417,0.906 0.615,0.198 10 false CAFL 6.063,0.708 6.677,0.906 0.615,0.198 10 false CANL 0.906,1.938 1.365,2.135 0.458,0.198 10 false IG2 2.24,2.104 3.177,2.396 0.938,0.292 10 false A/BAG 3.948,1.927 5.135,2.375 1.188,0.448 10 false from IG Circuit 0.979,2.563 1.292,2.76 0.313,0.198 10 false E1 0.969,3.177 1.281,3.375 0.313,0.198 10 false E2 0.104,4.177 2.26,4.615 2.156,0.438 10 false Yaw Rate and Acceleration Sensor (Airbag ECU Assembly) 0.115,4.01 0.469,4.208 0.354,0.198 10 false D10 3.469,3.135 5.583,3.375 2.115,0.24 10 false : CAN Communication Line 5.115,4.063 7.031,4.406 1.917,0.344 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.125,3.875 5.583,4.073 0.458,0.198 10 false A6 5.771,1.135 6.083,1.333 0.313,0.198 10 false 27 5.771,0.521 6.083,0.719 0.313,0.198 10 false 43 1.302,0.521 1.615,0.719 0.313,0.198 10 false 27 1.302,1.135 1.615,1.333 0.313,0.198 10 false 26 1.302,1.813 1.615,2.01 0.313,0.198 10 false 36 1.313,2.438 1.625,2.635 0.313,0.198 10 false 33 1.302,3.052 1.615,3.25 0.313,0.198 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag ECU assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE



Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the D10 yaw rate and acceleration sensor (airbag ECU assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-36 (IG2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-33 (E1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
D10-32 (E2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

Reconnect the D10 yaw rate and acceleration sensor (airbag ECU assembly) connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C14D71C is not output A
C14D71C is output B



Post-procedure1

a.

None



A

B