Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0448071 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B605605N01
5.521,2.083 6.208,2.083 true 6.333,0.521 6.854,0.521 false 6.365,0.198 6.885,0.198 false 1.094,2.49 1.615,2.49 true 2.135,3.083 2.5,3.083 true 6.188,0.063 6.469,0.417 0.281,0.354 18 true 1 6.198,0.385 6.479,0.74 0.281,0.354 18 true 2 6.26,1.958 6.542,2.313 0.281,0.354 18 true 3 0.917,2.344 1.198,2.698 0.281,0.354 18 true 4 1.958,2.958 2.24,3.313 0.281,0.354 18 false 5 2.156,1.594 2.469,1.792 0.313,0.198 10 false x 2 3.177,2.281 3.49,2.479 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 CONSOLE BOX ASSEMBLY - - - -
4 NO. 2 CONSOLE BOX MOUNTING BRACKET 58996A - - -
5 AIRBAG SENSOR ASSEMBLY 89170A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Yaw rate and acceleration sensor (airbag ECU assembly) Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
Perform learning for the yaw rate and acceleration sensor
for Stereo Camera Type:
·

Dynamic radar cruise control system (for Stereo camera type)

·

Lane tracing assist system (for Stereo camera type)

·

Road sign assist system (for Stereo camera type)

·

Front radar sensor system (for Stereo camera type)

·

Pre-collision system (for Stereo camera type)


-
for Mono Camera Type:
·

Dynamic radar cruise control system (for Mono camera type)

·

Front camera system (for Mono camera type)

·

Lane tracing assist system (for Mono camera type)

·

Road sign assist system (for Mono camera type)

·

Front radar sensor system (for Mono camera type)

·

Pre-collision system (for Mono camera type)


Target Adjustment (Triangle Target):
(Click here)
Target Adjustment (Flat Surface Target):
(Click here)
Driving Adjustment:
(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

Hide 58810J 3.REMOVE CONSOLE BOX ASSEMBLY

Hide 58996A 4.REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET

a.
B593220


Hide 89170A 5.REMOVE AIRBAG SENSOR ASSEMBLY

a.
B605562C01
1.042,0.458 1.833,0.458 true 0.458,0.104 0.74,0.458 0.281,0.354 18 false i 4.49,0.156 4.771,0.51 0.281,0.354 18 false ii 0.813,0.375 1.042,0.604 0.229,0.229 10 true *a
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B593221C02
0.396,0.021 0.677,0.375 0.281,0.354 18 true i 1.906,2.781 2.188,3.135 0.281,0.354 18 true ii
V113147

Push the Connector Lock
V113148

Pull Out the Lock Lever


i.

Pull out each connector with its connector lock pushed to disconnect the 3 connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



ii.

Remove the 3 bolts and airbag sensor assembly.

NOTICE:

If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the airbag sensor assembly with a new one.