Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050062  Left Front Wheel Speed Sensor Signal Compare Failure  


DESCRIPTION

Refer to DTC C050012.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050062 Left Front Wheel Speed Sensor Signal Compare Failure Any of the following is detected:
·

A lowest wheel speed is 10 km/h (6 mph) or more, the difference between the highest and lowest wheel speeds is 2 km/h (1 mph) or less, and the rotation direction of any one of the wheels is not detected for 15 seconds or more.

·

A vehicle speed is 30 km/h (19 mph) or more and the rotation direction of one of the wheels is different from those of other 3 wheels as well as it is not detected for 1 second or more.

·

A vehicle speed is 100 km/h, the output of reverse signal continues for 1 second or more

·

A vehicle speed is 30 km/h or more, and the rotation direction of any one of the wheels is not detected while the other 3 wheels do not rotate in the same direction for 1 second or more.


Front speed sensor LH (front axle hub sub-assembly LH) Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C050062 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status A lowest wheel speed is 10 km/h (6 mph) or more, the difference between the highest and lowest wheel speeds is 2 km/h (1 mph) or less, and the rotation direction of any one of the wheels is not detected ○ - - -
A vehicle speed is 30 km/h (19 mph) or more and the rotation direction of one of the wheels is different from those of other 3 wheels as well as it is not detected - ○ - -
A vehicle speed is 100 km/h, the output of reverse signal continues for 1 second or more - - ○ -
A vehicle speed is 30 km/h or more, and the rotation direction of any one of the wheels is not detected while the other 3 wheels do not rotate in the same direction for 1 second or more - - - ○
Detection Time 15 seconds or more. 1 second or more. 1 second or more. 1 second or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT




NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C050062 is not output A
C050062 is output B



Post-procedure1

a.

None



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH