Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the rear television camera assembly and the radio and display receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1622 Back Camera Disconnected Open or Short Circuit in rear television camera signal
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly


Navigation System A

WIRING DIAGRAM

E402604E35
1.583,2.979 4.146,3.167 2.563,0.188 10 false Radio and Display Receiver Assembly 1.583,2.813 1.969,3.01 0.385,0.198 10 false D56 2.135,2.5 2.74,2.74 0.604,0.24 10 false CSLD 2.083,2.083 2.635,2.292 0.552,0.208 10 false CGND 2.344,1.646 2.729,1.844 0.385,0.198 10 false V- 2.313,1.25 2.698,1.448 0.385,0.198 10 false V+ 2.229,0.823 2.615,1.021 0.385,0.198 10 false CA+ 2.615,0.719 3,0.917 0.385,0.198 10 false 30 2.604,1.563 2.99,1.76 0.385,0.198 10 false 29 2.604,1.135 2.99,1.333 0.385,0.198 10 false 28 2.615,1.979 3,2.177 0.385,0.198 10 false 27 2.604,2.406 2.99,2.604 0.385,0.198 10 false 26 4.729,2.823 5.844,3.021 1.115,0.198 10 false K4 4.74,3 6.938,3.323 2.198,0.323 10 false Rear Television Camera Assembly 5.531,0.833 5.917,1.031 0.385,0.198 10 false CB+ 5.521,1.271 5.906,1.469 0.385,0.198 10 false CV+ 5.51,1.688 5.896,1.885 0.385,0.198 10 false CV- 5.51,2.104 6.104,2.375 0.594,0.271 10 false CGND 5.292,0.75 5.677,0.948 0.385,0.198 10 false 6 5.292,1.146 5.677,1.344 0.385,0.198 10 false 3 5.281,1.552 5.667,1.75 0.385,0.198 10 false 2 5.281,1.979 5.667,2.177 0.385,0.198 10 false 5 3.948,2.406 4.333,2.604 0.385,0.198 10 false * 0.146,3.406 1.271,3.615 1.125,0.208 10 false *: Shielded

PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON (READY).


d.

Change the shift position to R to display the rear image.


Procedure1

e.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

f.

None



A

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Disconnect the K4 rear television camera assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K4,D56)Location & Routing

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

K4-6 (CB+) - D56-30 (CA+) Always Below 1 Ω
K4-3 (CV+) - D56-28 (V+) Always Below 1 Ω
K4-2 (CV-) - D56-29 (V-) Always Below 1 Ω
K4-5 (CGND) - D56-27 (CGND) Always Below 1 Ω
K4-6 (CB+) - Body ground Always 10 kΩ or higher
K4-3 (CV+) - Body ground Always 10 kΩ or higher
K4-2 (CV-) - Body ground Always 10 kΩ or higher
K4-5 (CGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E402706C04
1.458,0.094 2.01,0.354 0.552,0.26 1.125,1.073 0.813,0.76 0.813,0.76 0.469,0.76 true 1.479,1.135 1.406,1.875 1.406,1.875 1.135,1.875 true 1.625,0.146 2.24,0.344 0.615,0.198 10 false D56 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.135,0.677 0.521,0.875 0.385,0.198 10 false CA+ 0.708,1.792 1.198,2 0.49,0.208 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-27 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-30 (CA+) - Body ground Ignition switch ON (READY) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Check the waveform of the rear television camera assembly using an oscilloscope.

E402705C07
0.885,0.292 1.375,0.583 0.49,0.292 0.333,2.271 0.5,2.271 0.5,2.271 0.688,1.406 true 1.198,2.302 1.031,2.302 1.031,2.302 0.771,1.417 true 2.708,2.281 2.875,2.281 2.875,2.281 3.042,1.688 true 3.49,2.292 3.323,2.292 3.323,2.292 3.135,1.615 true 5.094,2.167 5.26,2.167 5.26,2.167 5.427,1.573 true 5.885,2.208 5.719,2.208 5.719,2.208 5.531,1.531 true 1.01,0.365 1.469,0.563 0.458,0.198 10 false D56 0.083,0.073 0.542,0.271 0.458,0.198 10 false *a 2.49,0.021 2.948,0.219 0.458,0.198 10 false *b 4.927,0.042 5.385,0.24 0.458,0.198 10 false *c 0.115,2.188 0.573,2.385 0.458,0.198 10 false V- 1.271,2.219 1.875,2.406 0.604,0.188 10 false V+ 2.521,2.208 2.979,2.406 0.458,0.198 10 false *d 3.531,2.208 3.99,2.406 0.458,0.198 10 false *e 4.927,2.094 5.385,2.292 0.458,0.198 10 false *d 5.917,2.135 6.375,2.333 0.458,0.198 10 false *e 2.344,1.229 2.948,1.417 0.604,0.188 10 false GND 4.75,1.229 5.354,1.417 0.604,0.188 10 false GND
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -


HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) D56-28 (V+) - D56-29 (V-)
Tool setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON (READY), camera lens is not covered, displaying an image
Waveform 2: Ignition switch ON (READY), camera lens is covered, blacking out the screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE REAR TELEVISION CAMERA ASSEMBLY
5.REPLACE REAR TELEVISION CAMERA ASSEMBLY
a.

Replace the rear television camera assembly with a new or normally functioning one.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON (READY).


d.

Change the shift position to R to display the rear image.


Procedure1

e.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

f.

None



A

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY