Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or meter mirror sub-assembly* is not possible.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 2 junction connector


Navigation System A
B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Meter mirror sub-assembly power source circuit

·

Meter mirror sub-assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 2 junction connector


Navigation System A

*: w/ Headup Display


HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E436805E24
2.906,2.177 4.083,2.563 1.177,0.385 10 false Combination Meter Assembly 2.906,2 3.354,2.292 0.448,0.292 10 false D41 3.698,1.635 3.969,1.833 0.271,0.198 10 false ES 3.083,1.063 3.531,1.354 0.448,0.292 10 false B 3.073,1.49 3.365,1.688 0.292,0.198 10 false IG+ 2.813,0.979 3.26,1.271 0.448,0.292 10 false 22 2.823,1.406 3.271,1.698 0.448,0.292 10 false 21 4,1.24 4.448,1.531 0.448,0.292 10 false 7 3.99,0.958 4.438,1.25 0.448,0.292 10 false 8 3.99,1.531 4.438,1.823 0.448,0.292 10 false 31 4.313,0.927 4.542,1.125 0.229,0.198 10 false 14 4.365,1.229 4.531,1.417 0.167,0.188 10 false 3 5.531,0.927 5.979,1.219 0.448,0.292 10 false 13 5.531,1.24 5.979,1.531 0.448,0.292 10 false 2 5.927,0.938 6.375,1.229 0.448,0.292 10 false 5 5.833,1.865 7.031,2.25 1.198,0.385 10 false Radio and Display Receiver Assembly 5.927,1.229 6.375,1.521 0.448,0.292 10 false 6 5.833,1.698 6.135,1.875 0.302,0.177 10 false D56 6.094,1.052 6.531,1.25 0.438,0.198 10 false CNH1 6.104,1.344 6.51,1.542 0.406,0.198 10 false CNL1 0.313,1.031 1.677,1.281 1.365,0.25 10 false from Auxiliary Battery 0.573,1.458 1.677,1.708 1.104,0.25 10 false from IG2 D Relay 2.083,1.208 3.229,1.542 1.146,0.333 10 false METER 1.948,1.677 2.802,2.021 0.854,0.344 10 false IG2 D NO.1 3.021,4.115 4.125,4.49 1.104,0.375 10 false Meter Mirror Sub-assembly* 3.021,3.958 3.313,4.135 0.292,0.177 10 false D95 1.844,3.083 3.208,3.427 1.365,0.344 10 false MPX-B D NO.1 1.99,3.771 3.948,4.125 1.958,0.354 10 false IG1 D NO.1 0.208,3.573 1.667,3.823 1.458,0.25 10 false from IG1 D NO.1 Relay 4.521,4.74 6.073,4.938 1.552,0.198 10 false No. 2 Junction Connector 4.521,4.573 4.885,4.76 0.365,0.188 10 false D167 3.063,2.927 3.25,3.125 0.188,0.198 10 false B 3.073,3.604 3.26,3.823 0.188,0.219 10 false IG 3.688,3.406 3.958,3.625 0.271,0.219 10 false ES 3.656,2.865 3.969,3.063 0.313,0.198 10 false TX+ 3.688,3.156 3.948,3.365 0.26,0.208 10 false TX- 3.969,2.781 4.417,3.073 0.448,0.292 10 false 14 3.969,3.063 4.417,3.354 0.448,0.292 10 false 15 4.313,2.781 4.76,3.073 0.448,0.292 10 false 12 4.365,3.063 4.813,3.354 0.448,0.292 10 false 1 3.99,3.344 4.438,3.635 0.448,0.292 10 false 4 2.854,2.792 3.302,3.083 0.448,0.292 10 false 2 2.854,3.49 3.302,3.781 0.448,0.292 10 false 1 1,4.99 3.021,5.198 2.021,0.208 10 false : Local Bus Communication Line 3.677,1.344 3.917,1.521 0.24,0.177 10 false TX- 0.365,4.542 1.688,4.771 1.323,0.229 10 false *: w/ Headup Display 0.313,2.885 1.677,3.125 1.365,0.24 10 false from Auxiliary Battery 3.656,1.063 3.917,1.271 0.26,0.208 10 false TX+

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

B1324 and B1325 will not continue to output when clear DTC is performed even if the malfunction continues.


PROCEDURE

1.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
B1324 and B1325 are not output A
B1324 and B1325 are output B
Only B1324 is output C
Only B1325 is output D



A

B

2.CHECK LOCAL BUS

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

14.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY POWER SOURCE)
2.CHECK LOCAL BUS

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Result Proceed to
D167-13 - D167-2 is less than or equal to 54 Ω A
D167-13 - D167-2 is more than or equal to 70 Ω B
None of the above conditions are met C



Post-procedure1

c.

None



A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

B

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

C

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D95 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-14 (TX+) - D95-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D41 combination meter assembly connector.


c.

Connect the D167 No. 2 junction connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-8 (TX+) - D41-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D56 radio and display receiver assembly connector.


c.

Connect the D167 No. 2 junction connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-5 (CNH1) - D56-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D56 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-5 (CNH1) - D56-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 11 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the D41 combination meter assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-31 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-22 (B) - Body ground Ignition switch off 11 to 14 V
D41-21 (IG+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-14 - D167-3 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D41 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-8 (TX+) - D41-7 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the D95 meter mirror sub-assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-2 (B) - Body ground Ignition switch off 11 to 14 V
D95-1 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

15.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-12 - D167-1 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

16.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

18.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
16.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D167 No. 2 junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D167)Location & Routing

Click Connector(D167)Instrument Panel>Instrument Panel Wire>No. 2 CAN Junction Connector

D167-13 - D167-2 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

17.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
17.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D56 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-5 (CNH1) - D56-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D95 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D95)Location & Routing

Click Connector(D95)Instrument Panel>Instrument Panel Wire>Meter Mirror Sub-Assembly

D95-14 (TX+) - D95-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR