This DTC is output when an open circuit or short occurs in the communication line between a front side ultrasonic sensor (FRS sensor) and the clearance warning ECU assembly, or when a malfunction occurs in a front side ultrasonic sensor (FRS sensor) on the front.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AE587 | Ultrasonic Sensor (Front Right Side) Missing Message | Front side ultrasonic sensor (FRS sensor) lost communication | ·
Front side ultrasonic sensor (FRS sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Clearance Warning | A |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
Check the vehicle condition and work details.
| Result | Proceed to |
|---|---|
| The clearance warning ECU assembly or ultrasonic sensor has not been replaced | A |
| The clearance warning ECU assembly or ultrasonic sensor has been replaced | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION
Check that the connector is properly connected to the front side ultrasonic sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE587 is not output | A |
| C1AE587 is output | B |
A
B
Check that the connector is properly connected to the clearance warning ECU assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE587 is not output | A |
| C1AE587 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the A88 front side ultrasonic sensor (FRS sensor) connector.
Disconnect the G20 clearance warning ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A88,G20)Location & Routingewd_type=routing;type=c,c;code=A88,G20 Click Connector(G20)Body>Floor Wire / No. 3 Floor Wire>Clearance Warning ECU Assemblyewd_type=component;type=c;code=G20;pinno=7,5,6 |
||
| A88-4 (BI) - G20-7 (CSB1) | Always | Below 1 Ω |
| A88-5 (SI) - G20-5 (LIN1) | Always | Below 1 Ω |
| A88-6 (EI) - G20-6 (CSG1) | Always | Below 1 Ω |
| A88-4 (BI) or G20-7 (CSB1) - Body ground | Always | 10 kΩ or higher |
| A88-5 (SI) or G20-5 (LIN1) - Body ground | Always | 10 kΩ or higher |
| A88-6 (EI) or G20-6 (CSG1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the front side ultrasonic sensor (FRS sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| C1AE587 is not output | A |
| C1AE587 is output | B |
A
B