This DTC is stored if the parking assist ECU determines that the input/output signal communication with the rear television camera assembly is abnormal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Rear television camera assembly power supply malfunction | ·
Harness or connector ·
Rear television camera assembly ·
Parking assist ECU |
Rear Camera | A |
When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Pre-procedure1
Disconnect the G142 parking assist ECU connector.
Disconnect the K12 rear television camera assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G142,K12)Location & Routingewd_type=routing;type=c,c;code=G142,K12 Click Connector(G142)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECUewd_type=component;type=c;code=G142;pinno=2,1 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=4,3 |
||
| G142-2 (CB+) - K12-4 (CB+) | Always | Below 1 Ω |
| G142-1 (CGND) - K12-3 (CGND) | Always | Below 1 Ω |
| G142-2 (CB+) or K12-4 (CB+) - Body ground | Always | 10 kΩ or higher |
| G142-1 (CGND) or K12-3 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the K12 rear television camera assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=3 |
||
| K12-3 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=4 |
||
| K12-4 (CB+) - Body ground | Ignition switch ON | 7 to 8 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG