This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C162287 | Rear Camera Image Signal Missing Message | Open or short in the rear television camera signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Parking assist ECU |
Circumference Monitoring Camera Control Module | A |
When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Pre-procedure1
Disconnect the G142 parking assist ECU connector.
Disconnect the K12 rear television camera assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(G142,K12)Location & Routingewd_type=routing;type=c,c;code=G142,K12 Click Connector(G142)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECUewd_type=component;type=c;code=G142;pinno=2,4,3,1,5 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=4,6,5,3,7 |
||
| G142-2 (CB+) - K12-4 (CB+) | Always | Below 1 Ω |
| G142-4 (CV+) - K12-6 (CV+) | Always | Below 1 Ω |
| G142-3 (CV-) - K12-5 (CV-) | Always | Below 1 Ω |
| G142-1 (CGND) - K12-3 (CGND) | Always | Below 1 Ω |
| G142-5 (SGND) - K12-7 (SGND) | Always | Below 1 Ω |
| G142-2 (CB+) or K12-4 (CB+) - Body ground | Always | 10 kΩ or higher |
| G142-4 (CV+) or K12-6 (CV+) - Body ground | Always | 10 kΩ or higher |
| G142-3 (CV-) or K12-5 (CV-) - Body ground | Always | 10 kΩ or higher |
| G142-1 (CGND) or K12-3 (CGND) - Body ground | Always | 10 kΩ or higher |
| G142-5 (SGND) or K12-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the G142 parking assist ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (CGND) - Body ground | Always | Below 1 Ω |
| 3 (CV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the rear television camera assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=3 |
||
| K12-3 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assemblyewd_type=component;type=c;code=K12;pinno=4,3 |
||
| K12-4 (CB+) - K12-3 (CGND) | Ignition switch ON | 7 to 8 V |
| K12-4 (CB+) - K12-3 (CGND) | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG