Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455115 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor


Rear Camera A

WIRING DIAGRAM

E385092E11
0.365,0.604 1.792,0.844 1.427,0.24 10 false from Auxiliary Battery 0.26,1.167 1.729,1.448 1.469,0.281 10 false from IG1 D NO.1 Relay 2.073,1.375 3.042,1.552 0.969,0.177 10 false IG1 D NO.3 2.052,0.792 3.021,0.969 0.969,0.177 10 false MPX-B D NO.1 3.031,0.521 3.198,0.708 0.167,0.188 10 false 4 3.219,0.604 3.635,0.781 0.417,0.177 10 false BAT 3.208,1.167 3.49,1.344 0.281,0.177 10 false IG1 3.021,1.073 3.188,1.26 0.167,0.188 10 false 9 3.021,1.615 3.188,1.802 0.167,0.188 10 false 6 3.208,1.719 3.625,1.896 0.417,0.177 10 false ESS 3.177,2.177 3.5,2.354 0.323,0.177 10 false D34 3.167,2.333 4.219,2.542 1.052,0.208 10 false Steering Sensor 5.406,2.188 6.854,2.563 1.448,0.375 10 false Rear Television Camera Assembly 1.104,3.208 2.802,3.427 1.698,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following procedure.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the steering sensor connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D34)Location & Routing

Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensor

D34-6 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D34)Location & Routing

Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensor

D34-9 (IG1) - D34-6 (ESS) Ignition switch ON 11 to 14 V
D34-4 (BAT) - D34-6 (ESS) Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR