Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › STEERING ANGLE SENSOR
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454015 STEERING ANGLE SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  STEERING ANGLE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

C446181N02
1,0.417 6.167,3.417 5.167,3 6.167,1.75 6.667,1.75 false 2.156,2.323 2.156,2.552 2.156,2.552 2.573,2.552 false 3.75,1.5 4.25,1.5 false 6.542,0.177 6.875,0.177 false 6.719,1.625 7.052,2.042 0.333,0.417 18 false 2 2.969,2.438 3.302,2.771 0.333,0.333 18 false 3 3.583,1.448 3.917,1.698 0.333,0.25 10 false *1 6.385,0.052 6.719,0.469 0.333,0.417 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - - - -
3 STEERING SENSOR 89245B (Click here) - -

*1 SPIRAL CABLE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor Update ECU security key Vehicle control history (RoB) are stored (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click here(Click here)



Hide 2.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 89245B 3.REMOVE STEERING SENSOR

a.
C436426C03
3.938,1.198 3.333,1.719 3.333,1.719 3.948,0.708 true 2.833,1.313 2.635,0.76 true 5.01,0.938 4.417,0.938 true 0.646,0.188 0.927,0.542 0.281,0.354 18 false i 3.208,1.729 3.375,1.927 0.167,0.198 10 true *a 2.771,1.333 2.938,1.521 0.167,0.188 10 true *b 5.052,0.854 5.333,1.042 0.281,0.188 10 true *b
*a Guide *b Pin


i.

Disengage the 6 claws, 2 guides and 2 pins, and remove the steering sensor from the spiral cable sub-assembly.

NOTICE:

Do not damage the claws or pins of the spiral cable sub-assembly.