Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455115 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver

*: w/ Advanced Park

CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch signal input state DTC is not output Panoramic view monitor main switch (integration control and panel assembly)
SHIFT* Vehicle wire harness No. 2 semiconductor power integration ECU signal input state DTC is not output No. 2 semiconductor power integration ECU

WIRING DIAGRAM

E379405E32
5.083,3.417 6.396,3.625 1.313,0.208 10 false Parking Assist ECU 5.104,1.729 5.615,1.917 0.51,0.188 10 false BLSW 5.104,0.698 5.521,0.885 0.417,0.188 10 false REV* 3.01,1.615 3.292,1.865 0.281,0.25 10 false D 2.052,1.615 2.333,1.865 0.281,0.25 10 false E 1.99,2.26 4.979,2.646 2.99,0.385 10 false Panoramic View Monitor Switch 4.844,0.625 5.125,0.875 0.281,0.25 10 false 14 1.99,2.115 2.354,2.292 0.365,0.177 10 false D112 4.833,1.604 5.115,1.854 0.281,0.25 10 false 15 0.875,3.302 2.615,3.51 1.74,0.208 10 false : CAN Communication Line 5.073,3.26 5.396,3.448 0.323,0.188 10 false G13 0.271,0.656 2.302,1.25 2.031,0.594 10 false from No. 2 Semiconductor Power Integration ECU 3.208,1.604 3.354,1.802 0.146,0.198 10 false 5 1.844,1.615 2.021,1.802 0.177,0.188 10 false 2 2.823,3.281 4.177,3.479 1.354,0.198 10 false *: w/ Advanced Park

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the auxiliary battery cable is disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E372765

Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"SHIFT" displays "CHK" (red) B
"CAN" displays "CHK" (red) C



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)

B

4.CHECK BACK-UP LIGHT

C

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the D112 panoramic view monitor switch connector.


b.

Disconnect the G13 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G13,D112)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(D112)Instrument Panel>Instrument Panel Wire>Panoramic View Monitor Switch

G13-15 (BLSW) - D112-5 (D) Always Below 1 Ω
D112-2 (E) - Body ground Always Below 1 Ω
G13-15 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BACK-UP LIGHT
a.

Check that the back-up light comes on.

OK:

The back-up light comes on.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

5.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the parking assist ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G13)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

G13-14 (REV) - Body ground Ignition switch ON (READY)
Shift position in R
8 V or higher
G13-14 (REV) - Body ground Ignition switch ON (READY)
Shift position not in R
Below 3 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR