Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455115 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

for LHD
E301406E91
5.302,2.844 6.594,3.063 1.292,0.219 10 false Parking Assist ECU 5.292,2.698 5.667,2.885 0.375,0.188 10 false G13 5.302,2.125 5.74,2.333 0.438,0.208 10 false GND1 5.313,1.708 5.688,1.896 0.375,0.188 10 false ACC 5.302,1.302 5.51,1.49 0.208,0.188 10 false IG 5.302,0.865 5.563,1.063 0.26,0.198 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.125,2.021 5.281,2.219 0.156,0.198 10 false 4 3.229,1.042 4.25,1.24 1.021,0.198 10 false MPX-B D NO.2 3.24,1.458 4,1.646 0.76,0.188 10 false IG1 P NO.2 3.25,1.896 4.125,2.104 0.875,0.208 10 false ACC P NO.2 0.906,0.854 2.26,1.083 1.354,0.229 10 false from Auxiliary Battery 0.813,1.302 2.281,1.521 1.469,0.219 10 false from IG1 P NO.2 Relay 1.24,1.708 2.292,1.948 1.052,0.24 10 false from ACC Relay

for RHD
E301406E92
5.323,2.854 6.615,3.042 1.292,0.188 10 false Parking Assist ECU 5.313,2.708 5.625,2.896 0.313,0.188 10 false G13 5.302,2.125 5.75,2.323 0.448,0.198 10 false GND1 5.302,1.708 5.646,1.896 0.344,0.188 10 false ACC 5.302,1.313 5.51,1.5 0.208,0.188 10 false IG 5.302,0.865 5.552,1.042 0.25,0.177 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.125,2.021 5.281,2.219 0.156,0.198 10 false 4 3.229,1.052 4.188,1.25 0.958,0.198 10 false MPX-B D NO.2 3.26,1.458 4.042,1.667 0.781,0.208 10 false IG1 D NO.2 3.385,1.885 3.875,2.073 0.49,0.188 10 false ACC D 0.885,0.844 2.25,1.073 1.365,0.229 10 false from Auxiliary Battery 0.813,1.271 2.292,1.479 1.479,0.208 10 false from IG1 D NO.1 Relay 1.24,1.708 2.281,1.938 1.042,0.229 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


HINT:

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G13)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

G13-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G13)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

G13-1 (+B) - G13-4 (GND1) Ignition switch off 11 to 14 V
G13-2 (ACC) - G13-4 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G13-3 (IG) - G13-4 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR