Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P160600  Collision detected or Collision Sensor Connection (Open)  P160604  Collision detected or Collision Sensor Connection (Open) System Internal Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU and airbag ECU detect that a collision has occurred and shut off the system main relay.

The cause of this DTC may be one of the following:


·

Collision is detected

·

Detection sensor system malfunction

-

Airbag system malfunction

-

Communication malfunction between airbag ECU and EV control ECU

-

EV control ECU communication malfunction

-

EV control ECU malfunction



DESCRIPTION

The EV control ECU receives a signal that indicates a collision from the airbag ECU assembly to detect a collision. After detecting a collision, the EV control ECU shuts off the high voltage systems for safety.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P160600 Collision detected or Collision Sensor Connection (Open) Collision detection
A block signal is received from the airbag ECU assembly.
(1 trip detection logic)
·

Airbag ECU assembly

·

EV control ECU

·

Airbag system


Master Warning:
Comes on
EV A
P160604 Collision detected or Collision Sensor Connection (Open) System Internal Failure Collision detection
Multiple wiring malfunctions occur simultaneously.
(1 trip detection logic)
·

Airbag system

·

EV control ECU


Master Warning:
Comes on
EV A

HINT:

P160600 or P160604 is output, the hybrid system cannot be started unless the DTCs are cleared using the GTS.


Related Data List
DTC No. Data List
P160600
·

Collision Signal (Airbag)

·

Normal Signal for A/B ECU


P160604

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch off and wait for 10 minutes or more.

2.

Turn the ignition switch to ON (REAADY) and wait for 30 seconds or more.

3.

Turn the ignition switch off and wait for 10 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK VEHICLE FOR COLLISION DAMAGE
a.

Check the vehicle condition.

Result:
Result Proceed to
The vehicle is not damaged A
The vehicle is damaged B




A

2.CHECK DTC OUTPUT (EV)

B

REPAIR VEHICLE

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P160600 or P160604 only is output, or DTCs except the ones in the table below are also output A
Any of the following DTCs including pending DTCs are also output B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P06881F ECM/PCM Power Relay Sense Circuit Intermittent
P1C9E9F Hybrid/EV System Reset Stuck Off
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
U015187 Lost Communication with Restraints Control Module Missing Message

HINT:

P160600 or P160604 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P160600 is output A
P160604 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CLEAR DTC

B

6.CHECK DTC OUTPUT (EV)
4.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT (EV)
5.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P160600 is output A
P160600 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

6.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P160600 or P160604 and any DTCs in the table below are output NEXT


Relevant DTC
P310711 Lost Communication with Airbag System Control Module Circuit Short to Ground (Low)
P310715 Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open (High)
P310764 Lost Communication with Airbag System Control Module Signal Plausibility Failure
U015187 Lost Communication with Restraints Control Module Missing Message


Post-procedure1

a.

Turn the ignition switch off.



NEXT

GO TO DTC CHART (HYBRID CONTROL SYSTEM)