The cause of this malfunction may be the FC air compressor motor high-voltage circuit.
Check the FC air compressor motor internal resistance and the connection condition of the high-voltage line between the inverter and FC air compressor motor to check whether there is an open or short circuit.
| Area | Inspection |
|---|---|
| FC air compressor motor cable connection check | Check for the connection condition of the cable from the inverter to the FC air compressor with motor. |
| FC Air Compressor or FC air compressor motor cable | Check the FC air compressor with motor (including cable) internal resistance and the insulation resistance with body ground to check for an open or short circuit. |
This step is referenced from the procedures for each DTC.
If the inspection results below are normal, perform the next procedure for the referenced DTC.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.
Make sure to remove the service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.
The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.
Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.
| *a | Without waiting for 10 minutes |
After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.
Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.
If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.
After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the inverter cover from the inverter with converter assembly.
| *A | for LHD |
| *B | for RHD |
Check that the bolts for the FC air compressor motor cable are tightened to the specified torque, the FC air compressor motor cable is connected securely, and there are no contact problems.
T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Make sure that the tightening torque of the bolt is between 6.4 and 9.6 N*m (65 and 98 kgf*cm, 57 and 85 in.*lbf).
Disconnect the FC air compressor motor cable from the inverter with converter assembly.
Procedure1
Check for arc marks at the terminals for the FC air compressor motor cable.
| Result | Proceed to | |
|---|---|---|
| The terminals are connected securely and there are no contact problems. | There are no arc marks. | A |
| The terminals are not connected securely and there is a contact problem. | There are arc marks. | B |
| The terminals are not connected securely and there is a contact problem. | There are no arc marks. | C |
| The terminals are connected securely and there are no contact problems. | There are arc marks. | B |
Post-procedure1
Connect the FC air compressor motor cable to the inverter with converter assembly.
Install the inverter cover.
A
B
C
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the inverter cover from the inverter with converter assembly.
| *A | for LHD |
| *B | for RHD |
Disconnect the FC air compressor motor cable from the inverter with converter assembly.
Procedure1
| *A | for LHD |
| *B | for RHD |
| *1 | Shield Ground |
| *a | FC Air Compressor Motor Cable
(Inverter with Converter Assembly Side) |
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
If the FC air compressor motor temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o3)Location & Routingewd_type=routing;type=c;code=o3 Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o3;pinno=3,1,2 |
||
| o3-3 (W) - o3-1 (U) | Ignition switch off | 66.6 to 72.2 mΩ |
| o3-2 (V) - o3-3 (W) | Ignition switch off | 66.7 to 72.3 mΩ |
| o3-1 (U) - o3-2 (V) | Ignition switch off | 66.5 to 72.1 mΩ |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o2)Location & Routingewd_type=routing;type=c;code=o2 Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o2;pinno=1,3,2 |
||
| o2-1 (W) - o2-3 (U) | Ignition switch off | 66.6 to 72.2 mΩ |
| o2-2 (V) - o2-1 (W) | Ignition switch off | 66.7 to 72.3 mΩ |
| o2-3 (U) - o2-2 (V) | Ignition switch off | 66.5 to 72.1 mΩ |
To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).
R20 = Rt / {1 + 0.00393 X (T - 20)}
The calculation is based on the following:
R20: Resistance at 20°C (68°F) (mΩ)
Rt: Measured resistance (mΩ)
T: Temperature when the resistance is measured (°C)
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o3)Location & Routingewd_type=routing;type=c;code=o3 Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o3;pinno=3,2,1 |
||
| o3-3 (W) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o3-2 (V) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o3-1 (U) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o2)Location & Routingewd_type=routing;type=c;code=o2 Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o2;pinno=1,2,3 |
||
| o2-1 (W) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o2-2 (V) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o2-3 (U) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the FC air compressor motor cable.
Install the inverter cover.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the FC air compressor with motor assembly.
Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL
Check that the bolts for the FC air compressor motor cable are tightened to the specified torque, the FC air compressor motor cable is connected securely, and there are no contact problems.
T=10 N*m ( 102 kgf*cm, 7 ft.*lbf)
Disconnect the FC air compressor motor cable from the FC air compressor with motor assembly.
Procedure1
Check for arc marks at the terminals for the FC air compressor motor cable.
| Result | Proceed to | |
|---|---|---|
| The terminals are connected securely and there are no contact problems. | There are no arc marks. | A |
| The terminals are not connected securely and there is a contact problem. | There are arc marks. | B |
| The terminals are not connected securely and there is a contact problem. | There are no arc marks. | C |
| The terminals are connected securely and there are no contact problems. | There are arc marks. | B |
Post-procedure1
Connect the FC air compressor motor cable.
Install the FC air compressor with motor assembly.
A
B
C
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip and FC converter power outlet cable are not installed.
After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
| *A | for LHD |
| *B | for RHD |
Disconnect the FC air compressor motor cable from the inverter with converter assembly.
Remove the FC air compressor with motor assembly.
Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL
Disconnect the FC air compressor motor cable from the FC air compressor with motor assembly.
Procedure1
| *A | for LHD |
| *1 | Shield Ground |
| *a | FC Air Compressor Motor Cable |
| *A | for RHD |
| *1 | Shield Ground |
| *a | FC Air Compressor Motor Cable |
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o3,o1)Location & Routingewd_type=routing;type=c,c;code=o3,o1 Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o3;pinno=3,1,2 Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assemblyewd_type=component;type=c;code=o1;pinno=3,1,2 |
||
| o3-3 (W) or o1-3 (W) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o3-1 (U) or o1-1 (U) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o3-2 (V) or o1-2 (V) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o2,o1)Location & Routingewd_type=routing;type=c,c;code=o2,o1 Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o2;pinno=1,3,2 Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assemblyewd_type=component;type=c;code=o1;pinno=3,1,2 |
||
| o2-1 (W) or o1-3 (W) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o2-3 (U) or o1-1 (U) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
| o2-2 (V) or o1-2 (V) - Body ground and shield ground | Ignition switch off | 10 MΩ or higher |
Wrap the terminal of the FC air compressor motor cable with insulating tape to prevent them from coming into contact with body ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o3,o1)Location & Routingewd_type=routing;type=c,c;code=o3,o1 Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o3;pinno=3,1,2 Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assemblyewd_type=component;type=c;code=o1;pinno=3,1,2 |
||
| o3-3 (W) - o1-3 (W) | Ignition switch off | Below 1 Ω |
| o3-1 (U) - o1-1 (U) | Ignition switch off | Below 1 Ω |
| o3-2 (V) - o1-2 (V) | Ignition switch off | Below 1 Ω |
| o3-3 (W) - o1-1 (V) | Ignition switch off | 10 MΩ or higher |
| o3-2 (V) - o1-1 (U) | Ignition switch off | 10 MΩ or higher |
| o3-1 (U) - o1-3 (W) | Ignition switch off | 10 MΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(o2,o1)Location & Routingewd_type=routing;type=c,c;code=o2,o1 Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assemblyewd_type=component;type=c;code=o2;pinno=1,3,2 Click Connector(o1)Engine Compartment>FC Air Compressor Motor Cable Assembly>FC Air Compressor with Motor Assemblyewd_type=component;type=c;code=o1;pinno=3,1,2 |
||
| o2-1 (W) - o1-3 (W) | Ignition switch off | Below 1 Ω |
| o2-3 (U) - o1-1 (U) | Ignition switch off | Below 1 Ω |
| o2-2 (V) - o1-2 (V) | Ignition switch off | Below 1 Ω |
| o2-1 (W) - o1-1 (V) | Ignition switch off | 10 MΩ or higher |
| o2-2 (V) - o1-1 (U) | Ignition switch off | 10 MΩ or higher |
| o2-3 (U) - o1-3 (W) | Ignition switch off | 10 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the FC air compressor motor cable.
Install the inverter with converter assembly.
OK
NG