| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B000412 | Driver Knee Bolster Deployment Control Circuit Short to Battery | One of the following conditions is met:
·
The airbag ECU assembly detects a short circuit to B+ signal in the driver side knee squib circuit for 0.5 seconds. ·
A lower No. 1 instrument panel airbag assembly malfunction. ·
An airbag ECU assembly malfunction. |
·
Wire harness ·
Lower No. 1 instrument panel airbag assembly ·
Airbag ECU assembly |
Comes on | SRS Airbag | A | Applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B000412 is output | A |
| History B000412 is output | B |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Disconnect the airbag ECU assembly connector.
Disconnect the lower No. 1 instrument panel airbag assembly connector.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the connectors are not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *4 | SST |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
Connect the connector to the airbag ECU assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the lower No. 1 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B000412 is not output | A |
| B000412 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Disconnect SST from connector C.
A
B
Pre-procedure1
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
Disconnect the D10 airbag ECU assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D48)Location & Routingewd_type=routing;type=c;code=D48 Click Connector(D48)Instrument Panel>Instrument Panel Wire>No. 1 Lower Instrument Panel Airbag Assemblyewd_type=component;type=c;code=D48;pinno=1,2 |
||
| D48-1 (DK+) - Body ground | Ignition switch ON | Below 1 V |
| D48-2 (DK-) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
OK
NG
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Wire Harness |
Connect the airbag ECU assembly connector.
Connect the lower No. 1 instrument panel airbag assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B000412 is not output | A |
| B000412 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
To perform the simulation method, enter check mode (signal check) with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B